What Type of Oil Does a 2018 Yamaha PW50 Dirt Bike Take?

Shop parts for a 2018 Yamaha PW50 Dirt Bike.

Start With the Engine Type: The PW50 Is a Two-Stroke

The 2018 Yamaha PW50 runs a 49cc air-cooled two-stroke single, and that one fact shapes every oil question you'll ask about the bike. A two-stroke doesn't carry a crankcase full of engine oil the way a four-stroke does. Lubrication for the piston, rings, and bearings arrives through the fuel charge itself, which means the oil that matters most is the two-stroke oil burned along with the gasoline. The PW50 also carries a separate transmission and a shaft final drive, each with its own lubrication needs. So the honest answer to “what oil does it take” is really three answers: two-stroke oil for the engine, gear oil for the transmission, and gear oil for the shaft drive housing.

How the PW50 Delivers Its Two-Stroke Oil

Yamaha equipped the PW50 with an oil injection system rather than requiring the rider to pre-mix fuel at the pump. A small oil tank sits on the bike, and a pump meters two-stroke oil into the intake tract in proportion to throttle and engine speed. That's a genuinely convenient setup for a machine aimed at young riders, because it removes the guesswork of measuring oil into a gas can at every fill-up. Your job as the owner is simply to keep that tank topped off with a quality two-stroke oil and to confirm the pump is functioning. If the tank runs dry, the engine gets no lubrication at all, and a small two-stroke will seize quickly.

What Two-Stroke Oil to Put in the Tank

For the injection tank, use a two-stroke oil formulated for injector systems. Most modern two-stroke oils sold for dirt bikes are synthetic or semi-synthetic blends designed to burn cleanly, resist carbon buildup on the piston crown and exhaust port, and keep the spark plug from fouling. Yamaha's own two-stroke oil is a natural first choice, and any reputable motorcycle-specific two-stroke oil rated for injection use will serve well. Oils labeled only for outboard motors or chainsaws are formulated for different combustion temperatures and duty cycles, so a dedicated dirt bike two-stroke oil is the better call. It's inexpensive relative to the cost of a top-end rebuild, and the PW50's oil tank holds enough for many hours of riding.

If You Decide to Run Premix Instead

Some PW50 owners remove or disable the injection system and run pre-mixed fuel instead, usually because they want a known, fixed ratio or because they're troubleshooting the pump. If you go that route, common two-stroke premix ratios fall in the 32:1 to 50:1 range, with 40:1 and 50:1 being typical for modern synthetic oils. The exact ratio matters: too little oil starves the top end, while too much fouls plugs, loads up the exhaust, and makes the bike run rich and smoky. If you're converting a PW50 to premix, confirm the ratio recommended for the oil you're using and stick to it consistently. Never run straight gasoline in a two-stroke, whether injected or pre-mixed.

Transmission Oil: A Separate Service

The PW50 uses a wet centrifugal clutch and a multi-speed transmission that share a common oil bath, and that oil is completely separate from the two-stroke oil burned in the engine. This is the fluid that lubricates the gears, bearings, and clutch assembly, and it needs periodic replacement just like the oil in any gearbox. Most small two-stroke dirt bikes in this class commonly spec a motorcycle-specific 10W-30 or 10W-40, or a dedicated gear oil, and the PW50 fits that pattern. Because the clutch runs wet in the same oil, use a motorcycle-specific product rather than a car engine oil — automotive oils with friction modifiers can cause clutch slip and inconsistent engagement.

The Shaft Drive Has Its Own Gear Oil

One detail that surprises new PW50 owners is that the bike is shaft-driven rather than chain-driven. That means there's a final drive gear case at the rear wheel holding its own supply of gear oil, and it's a third fluid to keep an eye on. Shaft drive is wonderfully low-maintenance compared to a chain — no adjustment, no lubrication routine, no sprocket wear — but the gear case oil still needs its level checked and the fluid replaced on a sensible schedule. Because the quantity is small, a leak or a low level can go unnoticed until the gears start making noise, so it's worth a glance whenever you're doing other maintenance.

Why the Correct Oil Actually Matters Here

On a 49cc two-stroke turning high rpm with a young rider aboard, oil quality has an outsized effect on how long the top end lasts. The wrong two-stroke oil, or a lean oil ratio, accelerates piston and cylinder wear and can end in a seizure. The wrong transmission oil can make the clutch grab or slip and shorten gear life. Neglecting the shaft drive gear oil can turn a cheap fluid change into an expensive final drive repair. None of these are exotic failure modes — they're the ordinary consequences of using the wrong fluid or letting a level run low.

Confirming the Exact Specs for Your Bike

The guidance above reflects what's typical for the PW50 and for small two-stroke dirt bikes generally, and it will get you riding with the right fluids in the right places. For the precise oil type, the exact transmission oil viscosity, and the correct fill quantities, check your owner's manual or ask a Yamaha dealer — it's a two-minute confirmation that removes any doubt. Once you know those numbers, keeping a PW50 properly lubricated is one of the simplest maintenance routines in motorcycling.

Related Shopping Categories

Shop Oils and Fluids for a 2018 Yamaha PW50 Dirt Bike.

Shop Oil for a 2018 Yamaha PW50 Dirt Bike.

Shop Air Filters and Oil for a 2018 Yamaha PW50 Dirt Bike.

Shop Transmission for a 2018 Yamaha PW50 Dirt Bike.

Shop Oil Filters for a 2018 Yamaha PW50 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.