Replacing the Fuel Line on a 2024 Sherco 300 SE FACTORY

Shop parts for a 2024 Sherco 300 SE FACTORY Dirt Bike.

Rubber fuel hose is among the cheapest parts on a 2024 Sherco 300 SE FACTORY and one of the few that can end a ride outright. It hardens, cracks, and weeps fuel where you cannot see it, eventually either starving the engine or putting gasoline somewhere it should never be. Swapping it needs no specialty tools and no shop time.

Warning Signs Your 300 SE FACTORY Needs a New Line

A fuel line rarely fails without hinting first. Run through this list before loading the 300 SE FACTORY up, particularly if the bike has been sitting.

  • Fuel staining at either fitting. Seepage shows up at the barbs before anywhere else.
  • Persistent gasoline smell. If you smell fuel with the bike cold and untouched, something is leaking.
  • Cracks that appear when you flex the hose. Dry rot hides at rest and reveals itself the moment rubber bends.
  • Swelling or a soft, mushy section. The opposite of hardening and just as bad — usually chemical attack.
  • Surging or dying under load. Restricted flow mimics fuel starvation and gets misdiagnosed as a jetting problem.

Confirming the Fuel System on Your 2024 Sherco 300 SE FACTORY

Fuel delivery on the 2024 Sherco 300 SE FACTORY is carbureted, so the plumbing is about as simple as it gets on a two-stroke dirt bike — tank, petcock, hose, carburetor. That petcock is the most useful thing about this job. Turn it off and the fuel stops, which means no siphoning and no fighting gravity while you work.

Why This Part Wears Out at All

Rubber fuel line fails for reasons that have little to do with how hard you ride. Age drives it: the plasticizers keeping the hose flexible slowly migrate out, and pliable rubber turns stiff and glassy, so a small flex — bolting the tank down, rocking the bike onto a stand — opens a hairline crack. Dry, hot storage accelerates that, pulling volatiles out faster than a temperate garage would. Ethanol-blended pump fuel left sitting in the hose adds a second mechanism, attacking the inner wall and leaving gum that can flake into the fuel path on a 2024 Sherco 300 SE FACTORY.

Parts, Tools, and a Safe Workspace

Assemble everything first. Once the line is off, you do not want to be driving to the parts store with an open fuel system.

  • Replacement fuel line in the correct inside diameter and length for your 2024 Sherco 300 SE FACTORY. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

Before the first fitting comes loose, handle the safety side. Gasoline vapor pools low and finds ignition sources you would never consider, including pilot lights across the room. Ventilate properly, keep fuel in a closed container, wear eye protection, and never open the system on a hot engine.

Removing the Old Fuel Line

Shut the petcock off first. That single step keeps this job clean on a carbureted 300 SE FACTORY — with the valve closed, the tank stays full and the only fuel to manage is what is already past the valve.

Empty the carburetor next. Attach a length of clear hose to the float bowl drain nipple, direct it into your container, and open the drain screw. A minute later the bowl is dry and you can work without fuel running down your arm.

With the fuel handled, address the clamps at each end. Squeeze spring clamp tabs together with pliers and walk the clamp down the hose, or loosen a screw clamp with a driver. The hose is usually the hard part: years of heat cycling effectively glue it to the barb. Twist first to break the bond, then pull straight off. When a line is badly hardened, cutting it off with a razor blade is safer for the fitting than prying at it.

Fitting the New Line

Use the removed hose as your measuring stick and cut the new one to match. On a 2024 Sherco 300 SE FACTORY the correct length stays clear of moving and hot components while still absorbing engine movement without pulling on either fitting. Square off both ends with a sharp blade.

Start at the petcock. Work the hose on until the barb is fully buried — a partial seat is the most common cause of a post-repair leak. Warming a stiff hose helps it slide; lubricating the fitting does not. Leave grease and oil out entirely, since either prevents the rubber gripping properly and can end up inside the carburetor.

Then connect the carburetor side and dry-fit before clamping. Mount the tank if it was removed and verify the hose is not trapped, stretched, or resting on the head. Once the routing looks right, place a clamp at each end over the fitting itself and bring it to snug. New spring clamps are hard to overdo; screw clamps need restraint.

Verifying the Repair

Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.

Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.

Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our general guide to replacing a dirt bike fuel line.

Related Shopping Categories

Shop Fuel Lines for a 2024 Sherco 300 SE FACTORY Dirt Bike.

Shop Fuel Line Clamps for a 2024 Sherco 300 SE FACTORY Dirt Bike.

Shop Petcocks for a 2024 Sherco 300 SE FACTORY Dirt Bike.

Shop Fuel Filters for a 2024 Sherco 300 SE FACTORY Dirt Bike.

Shop Fuel Stabilizer for a 2024 Sherco 300 SE FACTORY Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.