How the Fuel Line Comes Off and Goes Back On — 2020 Yamaha PW50
Shop parts for a 2020 Yamaha PW50 Dirt Bike.
Rubber fuel hose is among the cheapest parts on a 2020 Yamaha PW50 and one of the few that can end a ride outright. It hardens, cracks, and weeps fuel where you cannot see it, eventually either starving the engine or putting gasoline somewhere it should never be. Swapping it needs no specialty tools and no shop time.
Start by Tracing the Fuel Path
Before anything comes apart, confirm what you have. The 2020 Yamaha PW50 is carbureted, identifiable by the petcock threaded into the bottom of the tank and a plain rubber hose running to the carburetor inlet. No fuel pump sits in the circuit and no pressure needs relieving, which removes the most awkward part of this repair.
Why This Part Wears Out at All
Two things degrade a fuel line: time, and what sits inside it. Rubber loses flexibility as it ages, and a hose that spent eight years on a 2020 Yamaha PW50 has been hardening the whole time, ridden or parked. Hardened rubber cannot absorb vibration, so it cracks where it stretches over a fitting. Ethanol-blended gasoline is the other half — fuel sitting unused for months attracts moisture and breaks down, which is rough on hose material and leaves varnish behind. Add a dry climate baking out what flexibility remains, and a line that looked fine last season can be brittle by spring.
Warning Signs Your PW50 Needs a New Line
Fuel line problems show up two ways: something you see and smell, or something you feel while riding. Both are worth taking seriously on a PW50.
- Evidence on the ground. A drip or dark patch under the bike after it sits overnight.
- The smell of raw gasoline. Noticeable with the engine cold and unrun.
- Surface cracking on the hose. Especially at bends and where the line slides over fittings.
- Weeping under light pressure. Push gently near a fitting and watch for moisture at the joint.
- Fuel starvation symptoms. Bogging or cutting out as though the tank ran dry when it clearly has not.
Getting Set Up Before You Start
This is a low-cost job, and most of the preparation is about containing fuel rather than turning wrenches.
- Replacement fuel line in the correct inside diameter and length for your 2020 Yamaha PW50. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
A word on handling fuel, because this is the part with real consequences: gasoline vapor is heavier than air and will travel across a floor to any spark or flame. Open the door, shut off pilot lights, cap your container, and let the bike cool. Gloves and eye protection are not optional.
Removing the Old Fuel Line
Close the petcock. Everything downstream of that valve is the only fuel you need to deal with, which on a 2020 Yamaha PW50 amounts to a few ounces in the line and float bowl.
Get that remaining fuel into a container rather than onto the floor. The float bowl drain screw is purpose-built for this — slip a hose over the nipple, aim it into your catch can, and crack the screw open. If you would rather drain the whole tank, do it now with the hose routed into the container.
Then release both clamps and work the hose off the fittings. Pliers handle spring clamps; a flat screwdriver handles screw clamps. Slide each clamp well back so it cannot fight you. To separate a stubborn hose from a barb, rotate it a quarter turn to shear the bond before pulling. If the rubber has gone hard enough that it will not release, split it with a knife along its length — the hose is being replaced anyway, and the fittings are what matter.
Installing the Replacement Hose
Trim the replacement to the same length as the original. Guessing causes problems at both ends of the range — excess hose finds something hot to lean against, and a short hose loads the fittings every time the engine moves. Cut cleanly and squarely.
Fit the tank-side end first, sliding the hose past the full barb until it bottoms out. If the line is stiff from sitting on a shelf, dip the end in hot water. Do not lubricate: no grease, no oil, no assembly lube on a fuel fitting. Beyond weakening the seal, it introduces contamination into the fuel your PW50 is about to run.
Connect the carburetor end and look at the whole run before securing anything. The hose should mirror the factory routing with clearance from the exhaust and no kinks. Then set both clamps directly over the barbed sections and tighten just enough to compress the rubber. Over-torquing a screw clamp scores the hose and creates a leak path over time.
Wrapping Up and Checking Your Work
Restore fuel flow and watch. Open the petcock on your 2020 Yamaha PW50 and leave the bike sitting several minutes with clean cardboard underneath. Gravity finds a poor seal quickly. Look at both fittings with good light, and run a dry fingertip around each joint — fuel is easier to feel than to see.
Then start the engine and check again warm. Vibration and heat expose leaks a static test misses. If you see weeping at a clamp, do not simply crank it tighter; pull the joint apart and confirm the hose was fully seated on the barb, because an unseated hose will not seal at any clamp torque.
Finally, tidy up. Dispose of drained fuel properly rather than returning it to the tank if it looks cloudy or smells stale, and check the new hose after your first ride or two — new rubber takes a small set as it conforms to the fitting. For more background on how fuel quality and storage habits shorten hose life, our full guide to dirt bike fuel line care covers that ground in detail.
Related Shopping Categories
Shop Fuel Lines for a 2020 Yamaha PW50 Dirt Bike.
Shop Fuel Line Clamps for a 2020 Yamaha PW50 Dirt Bike.
Shop Petcocks for a 2020 Yamaha PW50 Dirt Bike.
Shop Fuel Filters for a 2020 Yamaha PW50 Dirt Bike.
Shop Fuel Stabilizer for a 2020 Yamaha PW50 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.