Swapping the Fuel Line on Your 2018 Suzuki RM85
Shop parts for a 2018 Suzuki RM85 Dirt Bike.
A cracked fuel line seems trivial until it strands you at the far end of a trail or drips onto a hot pipe. On a 2018 Suzuki RM85, the fuel line is a short, inexpensive piece of rubber doing a job with zero tolerance for failure — and replacing it is well within reach with basic hand tools and about half an hour.
Confirming the Fuel System on Your 2018 Suzuki RM85
Fuel delivery on the 2018 Suzuki RM85 is carbureted, so the plumbing is about as simple as it gets on a two-stroke dirt bike — tank, petcock, hose, carburetor. That petcock is the most useful thing about this job. Turn it off and the fuel stops, which means no siphoning and no fighting gravity while you work.
Warning Signs Your RM85 Needs a New Line
Catching a bad line early is mostly about paying attention during routine checks. On a 2018 Suzuki RM85, these signals should send you looking at the hose.
- Wet spots on the frame or cases. Fuel evaporates fast, so look for residue rather than liquid.
- Fuel odor that will not clear. A leak too small to see is still large enough to smell.
- Hairline splits near the clamps. The clamped section takes the most stress and cracks first.
- Hose that holds its bend. If the line refuses to straighten, the rubber has hardened.
- Symptoms resembling a fueling fault. Bogging on hills or running lean with a full tank.
What Actually Kills a Fuel Line
Two things degrade a fuel line: time, and what sits inside it. Rubber loses flexibility as it ages, and a hose that spent eight years on a 2018 Suzuki RM85 has been hardening the whole time, ridden or parked. Hardened rubber cannot absorb vibration, so it cracks where it stretches over a fitting. Ethanol-blended gasoline is the other half — fuel sitting unused for months attracts moisture and breaks down, which is rough on hose material and leaves varnish behind. Add a dry climate baking out what flexibility remains, and a line that looked fine last season can be brittle by spring.
What to Have on the Bench
This is a low-cost job, and most of the preparation is about containing fuel rather than turning wrenches.
- Replacement fuel line in the correct inside diameter and length for your 2018 Suzuki RM85. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
Before the first fitting comes loose, handle the safety side. Gasoline vapor pools low and finds ignition sources you would never consider, including pilot lights across the room. Ventilate properly, keep fuel in a closed container, wear eye protection, and never open the system on a hot engine.
Working the Original Hose Free
Petcock off, first thing. That valve is why a carbureted bike like the RM85 is forgiving here: shut it and the fuel stops moving.
Capture the fuel sitting downstream. Fit a clear hose to the float bowl drain nipple, run it to your container, and open the drain screw a couple of turns. The bowl empties in under a minute. Close the screw afterward, because a bowl that will not hold fuel is frustrating to diagnose later.
Clamps come next. Squeeze the ears of a spring clamp with pliers and slide it clear, or back off a screw clamp until it moves freely. Then persuade the hose off the barb with a twisting motion rather than a hard yank — old rubber bonds to metal, and a straight pull can bend a carburetor inlet or petcock spigot. When the line is truly seized, slice it lengthwise and peel it away.
Routing and Securing the New Line
Use the removed hose as your measuring stick and cut the new one to match. On a 2018 Suzuki RM85 the correct length stays clear of moving and hot components while still absorbing engine movement without pulling on either fitting. Square off both ends with a sharp blade.
Start at the petcock. Work the hose on until the barb is fully buried — a partial seat is the most common cause of a post-repair leak. Warming a stiff hose helps it slide; lubricating the fitting does not. Leave grease and oil out entirely, since either prevents the rubber gripping properly and can end up inside the carburetor.
Then connect the carburetor side and dry-fit before clamping. Mount the tank if it was removed and verify the hose is not trapped, stretched, or resting on the head. Once the routing looks right, place a clamp at each end over the fitting itself and bring it to snug. New spring clamps are hard to overdo; screw clamps need restraint.
Wrapping Up and Checking Your Work
Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.
Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.
Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our full guide to dirt bike fuel line care.
Related Shopping Categories
Shop Fuel Lines for a 2018 Suzuki RM85 Dirt Bike.
Shop Fuel Line Clamps for a 2018 Suzuki RM85 Dirt Bike.
Shop Petcocks for a 2018 Suzuki RM85 Dirt Bike.
Shop Fuel Filters for a 2018 Suzuki RM85 Dirt Bike.
Shop Fuel Stabilizer for a 2018 Suzuki RM85 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.