Replacing the Fuel Line on a 2017 Yamaha YZ250

Shop parts for a 2017 Yamaha YZ250 Dirt Bike.

If you have owned your 2017 Yamaha YZ250 more than a few seasons, the fuel line deserves a hard look. It is a wear item almost nobody thinks about until it fails, and the failure is rarely graceful. Replacing the hose costs a few dollars, and doing it early beats doing it trailside with a leaking tank.

Warning Signs Your YZ250 Needs a New Line

A fuel line rarely fails without hinting first. Run through this list before loading the YZ250 up, particularly if the bike has been sitting.

  • Fuel staining at either fitting. Seepage shows up at the barbs before anywhere else.
  • Persistent gasoline smell. If you smell fuel with the bike cold and untouched, something is leaking.
  • Cracks that appear when you flex the hose. Dry rot hides at rest and reveals itself the moment rubber bends.
  • Swelling or a soft, mushy section. The opposite of hardening and just as bad — usually chemical attack.
  • Surging or dying under load. Restricted flow mimics fuel starvation and gets misdiagnosed as a jetting problem.

Why This Part Wears Out at All

Two things degrade a fuel line: time, and what sits inside it. Rubber loses flexibility as it ages, and a hose that spent eight years on a 2017 Yamaha YZ250 has been hardening the whole time, ridden or parked. Hardened rubber cannot absorb vibration, so it cracks where it stretches over a fitting. Ethanol-blended gasoline is the other half — fuel sitting unused for months attracts moisture and breaks down, which is rough on hose material and leaves varnish behind. Add a dry climate baking out what flexibility remains, and a line that looked fine last season can be brittle by spring.

Start by Tracing the Fuel Path

The fuel system on your 2017 Yamaha YZ250 uses a carburetor, and the petcock is your shutoff. Fuel flows by gravity alone from tank to float bowl through one hose, secured at each end by a spring pinch clamp or a small screw clamp. That is the whole circuit, and it is why this job is beginner-friendly on a two-stroke machine.

Tools & Preparation

Nothing here is exotic, but having it within reach before you open the fuel system keeps the job from turning messy.

  • Replacement fuel line in the correct inside diameter and length for your 2017 Yamaha YZ250. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

Take the fuel handling seriously. Vapor sinks and spreads, so ventilation matters more than most people assume — work outside or with the door up, and kill any appliance with a standing pilot flame. Keep the drain container closed between pours and wait for the engine to cool.

Working the Original Hose Free

Shut the petcock off first. That single step keeps this job clean on a carbureted YZ250 — with the valve closed, the tank stays full and the only fuel to manage is what is already past the valve.

Empty the carburetor next. Attach a length of clear hose to the float bowl drain nipple, direct it into your container, and open the drain screw. A minute later the bowl is dry and you can work without fuel running down your arm.

With the fuel handled, address the clamps at each end. Squeeze spring clamp tabs together with pliers and walk the clamp down the hose, or loosen a screw clamp with a driver. The hose is usually the hard part: years of heat cycling effectively glue it to the barb. Twist first to break the bond, then pull straight off. When a line is badly hardened, cutting it off with a razor blade is safer for the fitting than prying at it.

Putting the Fresh Hose On

Cut the new hose to length using the old one as a template, adding nothing extra. Line that is too long sags into the engine or gets pinched when the tank is bolted down; too short and it tugs at the fittings under vibration. A clean square cut seals better than a ragged one.

Push the new line onto the petcock spigot first, far enough to cover the full barb. Stiff hose goes on more easily after thirty seconds in warm water. What you must not do is lubricate the fitting — no grease, no oil, no silicone. Any of it compromises the seal and can contaminate the fuel path on your 2017 Yamaha YZ250.

Position the carburetor end next, checking your routing against how the original sat. Then set the clamps over the barb area, about a quarter inch from the hose end, so they compress rubber against the raised portion of the fitting. Snug is the target with screw clamps, not tight — overtightening cuts into the hose and creates the leak you were preventing.

Leak Check Before You Ride

With the new line in place, open the petcock and stop. Let the 2017 Yamaha YZ250 sit five minutes over a clean surface and use that time to examine both joints under a flashlight. A properly seated hose stays completely dry; anything else needs attention before the wheels turn.

The running test comes second. Fire the engine, let it warm, and look again — expansion and vibration find seals that hold fine cold and still. When you find a weep, resist the urge to overtighten. Disconnect, verify the hose is pushed fully over the barb, and reassemble; that is nearly always the actual problem.

Wrap up by disposing of the drained fuel appropriately and taking another look at the connections after your next ride. On carbureted bikes an inline filter, if fitted, is a serviceable part worth replacing at the same time. For deeper background on keeping fuel lines healthy between seasons, our broader walkthrough on dirt bike fuel line replacement is a useful companion read.

Related Shopping Categories

Shop Fuel Lines for a 2017 Yamaha YZ250 Dirt Bike.

Shop Fuel Line Clamps for a 2017 Yamaha YZ250 Dirt Bike.

Shop Petcocks for a 2017 Yamaha YZ250 Dirt Bike.

Shop Fuel Filters for a 2017 Yamaha YZ250 Dirt Bike.

Shop Fuel Stabilizer for a 2017 Yamaha YZ250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.