Getting a Fresh Fuel Line Onto Your 2013 Yamaha TTR50
Shop parts for a 2013 Yamaha TTR50 Dirt Bike.
A cracked fuel line seems trivial until it strands you at the far end of a trail or drips onto a hot pipe. On a 2013 Yamaha TTR50, the fuel line is a short, inexpensive piece of rubber doing a job with zero tolerance for failure — and replacing it is well within reach with basic hand tools and about half an hour.
Know the TTR50 Fuel Layout First
The fuel system on your 2013 Yamaha TTR50 uses a carburetor, and the petcock is your shutoff. Fuel flows by gravity alone from tank to float bowl through one hose, secured at each end by a spring pinch clamp or a small screw clamp. That is the whole circuit, and it is why this job is beginner-friendly on a four-stroke machine.
Red Flags During a Pre-Ride Look
Most failing fuel lines warn you before letting go. The warnings are easy to dismiss, so it helps to know what you are looking at when you walk up to your 2013 Yamaha TTR50.
- A puddle or damp patch underneath. Even a slow weep leaves evidence, usually below the tank or carburetor.
- A strong fuel smell in the garage. Odor lingering a day after parking is not normal.
- Visible cracking. Bend the hose gently; fine cracks that open under flex mean the rubber is done.
- A hose that feels hard or glazed. Healthy line is soft and slightly tacky.
- Bogging or running lean. A collapsed or deteriorated line restricts flow, and the engine acts like the tank is nearly empty.
Tools & Preparation
Nothing here is exotic, but having it within reach before you open the fuel system keeps the job from turning messy.
- Replacement fuel line in the correct inside diameter and length for your 2013 Yamaha TTR50. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
One genuine safety note: gasoline vapor is heavier than air and travels along the floor toward anything that can ignite it. Work outdoors or with the door open, shut off any heater with a pilot light, keep the fuel container capped, and let a hot engine cool first.
Why Fuel Lines Harden, Crack, and Fail
Two things degrade a fuel line: time, and what sits inside it. Rubber loses flexibility as it ages, and a hose that spent eight years on a 2013 Yamaha TTR50 has been hardening the whole time, ridden or parked. Hardened rubber cannot absorb vibration, so it cracks where it stretches over a fitting. Ethanol-blended gasoline is the other half — fuel sitting unused for months attracts moisture and breaks down, which is rough on hose material and leaves varnish behind. Add a dry climate baking out what flexibility remains, and a line that looked fine last season can be brittle by spring.
Taking the Failed Hose Off
Turn the petcock to the off position. On the 2013 Yamaha TTR50 this is the valve underneath the tank, and closing it stops fuel at the source. If your petcock has a reserve position, confirm you are fully off rather than on reserve.
Drain what is trapped downstream. The simplest route is the carburetor float bowl drain — run a short hose from the drain nipple into your container, back the screw out, and let the bowl empty. Snug the screw back up afterward so you do not forget it.
Now free the clamps. Spring clamps come off by squeezing the tabs with pliers and sliding the clamp back along the hose; screw clamps need a few turns of a flat driver. With both retracted, twist the hose on the fitting to break the seal, then work it off. Hardened line often resists — a gentle rotating pull beats brute force, and if it truly will not budge, slit the hose lengthwise with a blade and peel it off rather than levering on the fitting.
Putting the Fresh Hose On
Trim the replacement to the same length as the original. Guessing causes problems at both ends of the range — excess hose finds something hot to lean against, and a short hose loads the fittings every time the engine moves. Cut cleanly and squarely.
Fit the tank-side end first, sliding the hose past the full barb until it bottoms out. If the line is stiff from sitting on a shelf, dip the end in hot water. Do not lubricate: no grease, no oil, no assembly lube on a fuel fitting. Beyond weakening the seal, it introduces contamination into the fuel your TTR50 is about to run.
Connect the carburetor end and look at the whole run before securing anything. The hose should mirror the factory routing with clearance from the exhaust and no kinks. Then set both clamps directly over the barbed sections and tighten just enough to compress the rubber. Over-torquing a screw clamp scores the hose and creates a leak path over time.
Final Checks and the First Start
Restore fuel flow and watch. Open the petcock on your 2013 Yamaha TTR50 and leave the bike sitting several minutes with clean cardboard underneath. Gravity finds a poor seal quickly. Look at both fittings with good light, and run a dry fingertip around each joint — fuel is easier to feel than to see.
Then start the engine and check again warm. Vibration and heat expose leaks a static test misses. If you see weeping at a clamp, do not simply crank it tighter; pull the joint apart and confirm the hose was fully seated on the barb, because an unseated hose will not seal at any clamp torque.
Finally, tidy up. Dispose of drained fuel properly rather than returning it to the tank if it looks cloudy or smells stale, and check the new hose after your first ride or two — new rubber takes a small set as it conforms to the fitting. For more background on how fuel quality and storage habits shorten hose life, our complete overview of dirt bike fuel line service covers that ground in detail.
Related Shopping Categories
Shop Fuel Lines for a 2013 Yamaha TTR50 Dirt Bike.
Shop Fuel Line Clamps for a 2013 Yamaha TTR50 Dirt Bike.
Shop Petcocks for a 2013 Yamaha TTR50 Dirt Bike.
Shop Fuel Filters for a 2013 Yamaha TTR50 Dirt Bike.
Shop Fuel Stabilizer for a 2013 Yamaha TTR50 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.