A Practical Fuel Line Walkthrough for the 2013 Suzuki RM85L
Shop parts for a 2013 Suzuki RM85L Dirt Bike.
A cracked fuel line seems trivial until it strands you at the far end of a trail or drips onto a hot pipe. On a 2013 Suzuki RM85L, the fuel line is a short, inexpensive piece of rubber doing a job with zero tolerance for failure — and replacing it is well within reach with basic hand tools and about half an hour.
Know the RM85L Fuel Layout First
Fuel delivery on the 2013 Suzuki RM85L is carbureted, so the plumbing is about as simple as it gets on a two-stroke dirt bike — tank, petcock, hose, carburetor. That petcock is the most useful thing about this job. Turn it off and the fuel stops, which means no siphoning and no fighting gravity while you work.
Warning Signs Your RM85L Needs a New Line
Fuel line problems show up two ways: something you see and smell, or something you feel while riding. Both are worth taking seriously on a RM85L.
- Evidence on the ground. A drip or dark patch under the bike after it sits overnight.
- The smell of raw gasoline. Noticeable with the engine cold and unrun.
- Surface cracking on the hose. Especially at bends and where the line slides over fittings.
- Weeping under light pressure. Push gently near a fitting and watch for moisture at the joint.
- Fuel starvation symptoms. Bogging or cutting out as though the tank ran dry when it clearly has not.
What to Have on the Bench
The parts list is short and the tool list shorter. Lay it out before breaking the first connection.
- Replacement fuel line in the correct inside diameter and length for your 2013 Suzuki RM85L. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
Take the fuel handling seriously. Vapor sinks and spreads, so ventilation matters more than most people assume — work outside or with the door up, and kill any appliance with a standing pilot flame. Keep the drain container closed between pours and wait for the engine to cool.
What Actually Kills a Fuel Line
The failure is chemical and thermal more than mechanical. Fuel hose stays soft because of additives in the rubber, and those additives leave over time — faster in heat, faster still in the dry air of an arid climate. A hose in that state has lost its ability to seal around a barb, so it seeps before it visibly splits. Fuel left standing does its own damage: ethanol blends draw in moisture and degrade after months of sitting, and the byproducts attack rubber and leave sticky residue. If your 2013 Suzuki RM85L winters with fuel in the system, the line ages on the calendar rather than the odometer.
Removing the Old Fuel Line
Shut the petcock off first. That single step keeps this job clean on a carbureted RM85L — with the valve closed, the tank stays full and the only fuel to manage is what is already past the valve.
Empty the carburetor next. Attach a length of clear hose to the float bowl drain nipple, direct it into your container, and open the drain screw. A minute later the bowl is dry and you can work without fuel running down your arm.
With the fuel handled, address the clamps at each end. Squeeze spring clamp tabs together with pliers and walk the clamp down the hose, or loosen a screw clamp with a driver. The hose is usually the hard part: years of heat cycling effectively glue it to the barb. Twist first to break the bond, then pull straight off. When a line is badly hardened, cutting it off with a razor blade is safer for the fitting than prying at it.
Getting the New Line Seated Properly
Use the removed hose as your measuring stick and cut the new one to match. On a 2013 Suzuki RM85L the correct length stays clear of moving and hot components while still absorbing engine movement without pulling on either fitting. Square off both ends with a sharp blade.
Start at the petcock. Work the hose on until the barb is fully buried — a partial seat is the most common cause of a post-repair leak. Warming a stiff hose helps it slide; lubricating the fitting does not. Leave grease and oil out entirely, since either prevents the rubber gripping properly and can end up inside the carburetor.
Then connect the carburetor side and dry-fit before clamping. Mount the tank if it was removed and verify the hose is not trapped, stretched, or resting on the head. Once the routing looks right, place a clamp at each end over the fitting itself and bring it to snug. New spring clamps are hard to overdo; screw clamps need restraint.
Wrapping Up and Checking Your Work
Open the fuel valve and let gravity do the testing. Give the RM85L a few minutes standing over clean cardboard, then inspect the tank-side and carburetor-side joints carefully. Wipe each dry first so new moisture is unmistakable.
Follow that with a running check. Start the engine, bring it to temperature, and look at both fittings again at idle — some leaks only appear once heat and vibration are in the system. A joint weeping under those conditions has a seating problem, not a clamp problem; pull it apart and push the hose fully home.
Then clean up and stay attentive for a ride or two. Dispose of old fuel properly, watch the clamps as the new rubber settles, and consider replacing an inline filter while the system is open. Anyone wanting more detail on what shortens fuel line life long term will find it in our full guide to dirt bike fuel line care.
Related Shopping Categories
Shop Fuel Lines for a 2013 Suzuki RM85L Dirt Bike.
Shop Fuel Line Clamps for a 2013 Suzuki RM85L Dirt Bike.
Shop Petcocks for a 2013 Suzuki RM85L Dirt Bike.
Shop Fuel Filters for a 2013 Suzuki RM85L Dirt Bike.
Shop Fuel Stabilizer for a 2013 Suzuki RM85L Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.