Replacing the Fuel Line on a 2011 Yamaha TW200
Shop parts for a 2011 Yamaha TW200 Dirt Bike.
If you have owned your 2011 Yamaha TW200 more than a few seasons, the fuel line deserves a hard look. It is a wear item almost nobody thinks about until it fails, and the failure is rarely graceful. Replacing the hose costs a few dollars, and doing it early beats doing it trailside with a leaking tank.
The Carbureted Setup on This TW200
The 2011 Yamaha TW200 runs a carbureted fuel system, which works in your favor. Fuel leaves the tank through a petcock — the small valve underneath — travels down a short rubber hose, and enters the carburetor at the float bowl inlet. You can shut fuel off at the source, and the line is a simple two-clamp affair with no pump pressure behind it.
Red Flags During a Pre-Ride Look
A fuel line rarely fails without hinting first. Run through this list before loading the TW200 up, particularly if the bike has been sitting.
- Fuel staining at either fitting. Seepage shows up at the barbs before anywhere else.
- Persistent gasoline smell. If you smell fuel with the bike cold and untouched, something is leaking.
- Cracks that appear when you flex the hose. Dry rot hides at rest and reveals itself the moment rubber bends.
- Swelling or a soft, mushy section. The opposite of hardening and just as bad — usually chemical attack.
- Surging or dying under load. Restricted flow mimics fuel starvation and gets misdiagnosed as a jetting problem.
Why Fuel Lines Harden, Crack, and Fail
It helps to treat fuel line as a consumable rather than a permanent part. The material is engineered to stay soft and seal against a barbed fitting, and it loses that ability gradually as heat cycling, sun exposure, and plain calendar age push it the same direction — a dry climate does it fastest. Fuel chemistry compounds the problem. Ethanol blends sitting through a long off-season absorb water and begin to separate, which is harder on rubber than fresh fuel and leaves gum behind. On a 2011 Yamaha TW200 stored more than ridden, that combination is the usual culprit.
Gathering Parts and Setting Up
The parts list is short and the tool list shorter. Lay it out before breaking the first connection.
- Replacement fuel line in the correct inside diameter and length for your 2011 Yamaha TW200. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
Before the first fitting comes loose, handle the safety side. Gasoline vapor pools low and finds ignition sources you would never consider, including pilot lights across the room. Ventilate properly, keep fuel in a closed container, wear eye protection, and never open the system on a hot engine.
Working the Original Hose Free
Shut the petcock off first. That single step keeps this job clean on a carbureted TW200 — with the valve closed, the tank stays full and the only fuel to manage is what is already past the valve.
Empty the carburetor next. Attach a length of clear hose to the float bowl drain nipple, direct it into your container, and open the drain screw. A minute later the bowl is dry and you can work without fuel running down your arm.
With the fuel handled, address the clamps at each end. Squeeze spring clamp tabs together with pliers and walk the clamp down the hose, or loosen a screw clamp with a driver. The hose is usually the hard part: years of heat cycling effectively glue it to the barb. Twist first to break the bond, then pull straight off. When a line is badly hardened, cutting it off with a razor blade is safer for the fitting than prying at it.
Installing the Replacement Hose
Trim the replacement to the same length as the original. Guessing causes problems at both ends of the range — excess hose finds something hot to lean against, and a short hose loads the fittings every time the engine moves. Cut cleanly and squarely.
Fit the tank-side end first, sliding the hose past the full barb until it bottoms out. If the line is stiff from sitting on a shelf, dip the end in hot water. Do not lubricate: no grease, no oil, no assembly lube on a fuel fitting. Beyond weakening the seal, it introduces contamination into the fuel your TW200 is about to run.
Connect the carburetor end and look at the whole run before securing anything. The hose should mirror the factory routing with clearance from the exhaust and no kinks. Then set both clamps directly over the barbed sections and tighten just enough to compress the rubber. Over-torquing a screw clamp scores the hose and creates a leak path over time.
Final Checks and the First Start
With the new line in place, open the petcock and stop. Let the 2011 Yamaha TW200 sit five minutes over a clean surface and use that time to examine both joints under a flashlight. A properly seated hose stays completely dry; anything else needs attention before the wheels turn.
The running test comes second. Fire the engine, let it warm, and look again — expansion and vibration find seals that hold fine cold and still. When you find a weep, resist the urge to overtighten. Disconnect, verify the hose is pushed fully over the barb, and reassemble; that is nearly always the actual problem.
Wrap up by disposing of the drained fuel appropriately and taking another look at the connections after your next ride. On carbureted bikes an inline filter, if fitted, is a serviceable part worth replacing at the same time. For deeper background on keeping fuel lines healthy between seasons, our complete overview of dirt bike fuel line service is a useful companion read.
Related Shopping Categories
Shop Fuel Lines for a 2011 Yamaha TW200 Dirt Bike.
Shop Fuel Line Clamps for a 2011 Yamaha TW200 Dirt Bike.
Shop Petcocks for a 2011 Yamaha TW200 Dirt Bike.
Shop Fuel Filters for a 2011 Yamaha TW200 Dirt Bike.
Shop Fuel Stabilizer for a 2011 Yamaha TW200 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.