Swapping the Fuel Line on Your 2000 KTM 300EXC

Shop parts for a 2000 KTM 300EXC Dirt Bike.

If you have owned your 2000 KTM 300EXC more than a few seasons, the fuel line deserves a hard look. It is a wear item almost nobody thinks about until it fails, and the failure is rarely graceful. Replacing the hose costs a few dollars, and doing it early beats doing it trailside with a leaking tank.

What You Are Working With on the 300EXC

The fuel system on your 2000 KTM 300EXC uses a carburetor, and the petcock is your shutoff. Fuel flows by gravity alone from tank to float bowl through one hose, secured at each end by a spring pinch clamp or a small screw clamp. That is the whole circuit, and it is why this job is beginner-friendly on a two-stroke machine.

Red Flags During a Pre-Ride Look

Catching a bad line early is mostly about paying attention during routine checks. On a 2000 KTM 300EXC, these signals should send you looking at the hose.

  • Wet spots on the frame or cases. Fuel evaporates fast, so look for residue rather than liquid.
  • Fuel odor that will not clear. A leak too small to see is still large enough to smell.
  • Hairline splits near the clamps. The clamped section takes the most stress and cracks first.
  • Hose that holds its bend. If the line refuses to straighten, the rubber has hardened.
  • Symptoms resembling a fueling fault. Bogging on hills or running lean with a full tank.

Why Fuel Lines Harden, Crack, and Fail

It helps to treat fuel line as a consumable rather than a permanent part. The material is engineered to stay soft and seal against a barbed fitting, and it loses that ability gradually as heat cycling, sun exposure, and plain calendar age push it the same direction — a dry climate does it fastest. Fuel chemistry compounds the problem. Ethanol blends sitting through a long off-season absorb water and begin to separate, which is harder on rubber than fresh fuel and leaves gum behind. On a 2000 KTM 300EXC stored more than ridden, that combination is the usual culprit.

Getting Set Up Before You Start

This is a low-cost job, and most of the preparation is about containing fuel rather than turning wrenches.

  • Replacement fuel line in the correct inside diameter and length for your 2000 KTM 300EXC. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

One genuine safety note: gasoline vapor is heavier than air and travels along the floor toward anything that can ignite it. Work outdoors or with the door open, shut off any heater with a pilot light, keep the fuel container capped, and let a hot engine cool first.

Removing the Old Fuel Line

Petcock off, first thing. That valve is why a carbureted bike like the 300EXC is forgiving here: shut it and the fuel stops moving.

Capture the fuel sitting downstream. Fit a clear hose to the float bowl drain nipple, run it to your container, and open the drain screw a couple of turns. The bowl empties in under a minute. Close the screw afterward, because a bowl that will not hold fuel is frustrating to diagnose later.

Clamps come next. Squeeze the ears of a spring clamp with pliers and slide it clear, or back off a screw clamp until it moves freely. Then persuade the hose off the barb with a twisting motion rather than a hard yank — old rubber bonds to metal, and a straight pull can bend a carburetor inlet or petcock spigot. When the line is truly seized, slice it lengthwise and peel it away.

Installing the Replacement Hose

Use the removed hose as your measuring stick and cut the new one to match. On a 2000 KTM 300EXC the correct length stays clear of moving and hot components while still absorbing engine movement without pulling on either fitting. Square off both ends with a sharp blade.

Start at the petcock. Work the hose on until the barb is fully buried — a partial seat is the most common cause of a post-repair leak. Warming a stiff hose helps it slide; lubricating the fitting does not. Leave grease and oil out entirely, since either prevents the rubber gripping properly and can end up inside the carburetor.

Then connect the carburetor side and dry-fit before clamping. Mount the tank if it was removed and verify the hose is not trapped, stretched, or resting on the head. Once the routing looks right, place a clamp at each end over the fitting itself and bring it to snug. New spring clamps are hard to overdo; screw clamps need restraint.

Confirming It Is Sealed

Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.

Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.

Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our evergreen guide to fuel line care and replacement.

Related Shopping Categories

Shop Fuel Lines for a 2000 KTM 300EXC Dirt Bike.

Shop Fuel Line Clamps for a 2000 KTM 300EXC Dirt Bike.

Shop Petcocks for a 2000 KTM 300EXC Dirt Bike.

Shop Fuel Filters for a 2000 KTM 300EXC Dirt Bike.

Shop Fuel Stabilizer for a 2000 KTM 300EXC Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.