Replacing the Fuel Line on a 1999 Yamaha RT100
Shop parts for a 1999 Yamaha RT100 Dirt Bike.
Fuel line replacement sits near the top of the high-value, low-difficulty maintenance list on a 1999 Yamaha RT100. The hose is short, the fittings are simple, and the payoff is a fuel system you can stop worrying about. What follows covers identifying what you have, spotting a line on its way out, and getting the new one leak-free.
The Carbureted Setup on This RT100
The 1999 Yamaha RT100 runs a carbureted fuel system, which works in your favor. Fuel leaves the tank through a petcock — the small valve underneath — travels down a short rubber hose, and enters the carburetor at the float bowl inlet. You can shut fuel off at the source, and the line is a simple two-clamp affair with no pump pressure behind it.
What Actually Kills a Fuel Line
Two things degrade a fuel line: time, and what sits inside it. Rubber loses flexibility as it ages, and a hose that spent eight years on a 1999 Yamaha RT100 has been hardening the whole time, ridden or parked. Hardened rubber cannot absorb vibration, so it cracks where it stretches over a fitting. Ethanol-blended gasoline is the other half — fuel sitting unused for months attracts moisture and breaks down, which is rough on hose material and leaves varnish behind. Add a dry climate baking out what flexibility remains, and a line that looked fine last season can be brittle by spring.
How a Failing Line Announces Itself
Catching a bad line early is mostly about paying attention during routine checks. On a 1999 Yamaha RT100, these signals should send you looking at the hose.
- Wet spots on the frame or cases. Fuel evaporates fast, so look for residue rather than liquid.
- Fuel odor that will not clear. A leak too small to see is still large enough to smell.
- Hairline splits near the clamps. The clamped section takes the most stress and cracks first.
- Hose that holds its bend. If the line refuses to straighten, the rubber has hardened.
- Symptoms resembling a fueling fault. Bogging on hills or running lean with a full tank.
Getting Set Up Before You Start
This is a low-cost job, and most of the preparation is about containing fuel rather than turning wrenches.
- Replacement fuel line in the correct inside diameter and length for your 1999 Yamaha RT100. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
A word on handling fuel, because this is the part with real consequences: gasoline vapor is heavier than air and will travel across a floor to any spark or flame. Open the door, shut off pilot lights, cap your container, and let the bike cool. Gloves and eye protection are not optional.
Getting the Old Line Out of the Way
Close the petcock. Everything downstream of that valve is the only fuel you need to deal with, which on a 1999 Yamaha RT100 amounts to a few ounces in the line and float bowl.
Get that remaining fuel into a container rather than onto the floor. The float bowl drain screw is purpose-built for this — slip a hose over the nipple, aim it into your catch can, and crack the screw open. If you would rather drain the whole tank, do it now with the hose routed into the container.
Then release both clamps and work the hose off the fittings. Pliers handle spring clamps; a flat screwdriver handles screw clamps. Slide each clamp well back so it cannot fight you. To separate a stubborn hose from a barb, rotate it a quarter turn to shear the bond before pulling. If the rubber has gone hard enough that it will not release, split it with a knife along its length — the hose is being replaced anyway, and the fittings are what matter.
Routing and Securing the New Line
Measure the replacement against the old line before cutting. Matching the original length keeps routing correct on the RT100, and a square cut gives the clamp a clean surface to seal against. Trim with a fresh blade rather than dull side cutters.
Slide the hose fully onto the tank-side fitting, past the barb and up against the shoulder. If the rubber resists, soften it in hot water; do not reach for lubricant. Grease or oil on a fuel fitting shows up later as a slow weep and can carry contamination into the carburetor.
Attach the carburetor end and check the shape of the run. The hose should follow the original path with no contact against cylinder or exhaust and no kink where it curves. Install fresh clamps over the fitting area rather than out on bare hose, and tighten only until the rubber is compressed — a screw clamp cranked down hard will eventually cut through.
Leak Check Before You Ride
Restore fuel flow and watch. Open the petcock on your 1999 Yamaha RT100 and leave the bike sitting several minutes with clean cardboard underneath. Gravity finds a poor seal quickly. Look at both fittings with good light, and run a dry fingertip around each joint — fuel is easier to feel than to see.
Then start the engine and check again warm. Vibration and heat expose leaks a static test misses. If you see weeping at a clamp, do not simply crank it tighter; pull the joint apart and confirm the hose was fully seated on the barb, because an unseated hose will not seal at any clamp torque.
Finally, tidy up. Dispose of drained fuel properly rather than returning it to the tank if it looks cloudy or smells stale, and check the new hose after your first ride or two — new rubber takes a small set as it conforms to the fitting. For more background on how fuel quality and storage habits shorten hose life, our evergreen guide to fuel line care and replacement covers that ground in detail.
Related Shopping Categories
Shop Fuel Lines for a 1999 Yamaha RT100 Dirt Bike.
Shop Fuel Line Clamps for a 1999 Yamaha RT100 Dirt Bike.
Shop Petcocks for a 1999 Yamaha RT100 Dirt Bike.
Shop Fuel Filters for a 1999 Yamaha RT100 Dirt Bike.
Shop Fuel Stabilizer for a 1999 Yamaha RT100 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.