Swapping the Fuel Line on Your 1998 KTM 50SX Pro Jr.

Shop parts for a 1998 KTM 50SX Pro Jr. Dirt Bike.

Fuel line replacement sits near the top of the high-value, low-difficulty maintenance list on a 1998 KTM 50SX Pro Jr.. The hose is short, the fittings are simple, and the payoff is a fuel system you can stop worrying about. What follows covers identifying what you have, spotting a line on its way out, and getting the new one leak-free.

Why This Part Wears Out at All

Rubber fuel line fails for reasons that have little to do with how hard you ride. Age drives it: the plasticizers keeping the hose flexible slowly migrate out, and pliable rubber turns stiff and glassy, so a small flex — bolting the tank down, rocking the bike onto a stand — opens a hairline crack. Dry, hot storage accelerates that, pulling volatiles out faster than a temperate garage would. Ethanol-blended pump fuel left sitting in the hose adds a second mechanism, attacking the inner wall and leaving gum that can flake into the fuel path on a 1998 KTM 50SX Pro Jr..

Know the 50SX Pro Jr. Fuel Layout First

Fuel delivery on the 1998 KTM 50SX Pro Jr. is carbureted, so the plumbing is about as simple as it gets on a two-stroke dirt bike — tank, petcock, hose, carburetor. That petcock is the most useful thing about this job. Turn it off and the fuel stops, which means no siphoning and no fighting gravity while you work.

Red Flags During a Pre-Ride Look

Fuel line problems show up two ways: something you see and smell, or something you feel while riding. Both are worth taking seriously on a 50SX Pro Jr..

  • Evidence on the ground. A drip or dark patch under the bike after it sits overnight.
  • The smell of raw gasoline. Noticeable with the engine cold and unrun.
  • Surface cracking on the hose. Especially at bends and where the line slides over fittings.
  • Weeping under light pressure. Push gently near a fitting and watch for moisture at the joint.
  • Fuel starvation symptoms. Bogging or cutting out as though the tank ran dry when it clearly has not.

Parts, Tools, and a Safe Workspace

This is a low-cost job, and most of the preparation is about containing fuel rather than turning wrenches.

  • Replacement fuel line in the correct inside diameter and length for your 1998 KTM 50SX Pro Jr.. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

One genuine safety note: gasoline vapor is heavier than air and travels along the floor toward anything that can ignite it. Work outdoors or with the door open, shut off any heater with a pilot light, keep the fuel container capped, and let a hot engine cool first.

Draining Down and Pulling the Line

Shut the petcock off first. That single step keeps this job clean on a carbureted 50SX Pro Jr. — with the valve closed, the tank stays full and the only fuel to manage is what is already past the valve.

Empty the carburetor next. Attach a length of clear hose to the float bowl drain nipple, direct it into your container, and open the drain screw. A minute later the bowl is dry and you can work without fuel running down your arm.

With the fuel handled, address the clamps at each end. Squeeze spring clamp tabs together with pliers and walk the clamp down the hose, or loosen a screw clamp with a driver. The hose is usually the hard part: years of heat cycling effectively glue it to the barb. Twist first to break the bond, then pull straight off. When a line is badly hardened, cutting it off with a razor blade is safer for the fitting than prying at it.

Installing the Replacement Hose

Trim the replacement to the same length as the original. Guessing causes problems at both ends of the range — excess hose finds something hot to lean against, and a short hose loads the fittings every time the engine moves. Cut cleanly and squarely.

Fit the tank-side end first, sliding the hose past the full barb until it bottoms out. If the line is stiff from sitting on a shelf, dip the end in hot water. Do not lubricate: no grease, no oil, no assembly lube on a fuel fitting. Beyond weakening the seal, it introduces contamination into the fuel your 50SX Pro Jr. is about to run.

Connect the carburetor end and look at the whole run before securing anything. The hose should mirror the factory routing with clearance from the exhaust and no kinks. Then set both clamps directly over the barbed sections and tighten just enough to compress the rubber. Over-torquing a screw clamp scores the hose and creates a leak path over time.

Confirming It Is Sealed

Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.

Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.

Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our evergreen guide to fuel line care and replacement.

Related Shopping Categories

Shop Fuel Lines for a 1998 KTM 50SX Pro Jr. Dirt Bike.

Shop Fuel Line Clamps for a 1998 KTM 50SX Pro Jr. Dirt Bike.

Shop Petcocks for a 1998 KTM 50SX Pro Jr. Dirt Bike.

Shop Fuel Filters for a 1998 KTM 50SX Pro Jr. Dirt Bike.

Shop Fuel Stabilizer for a 1998 KTM 50SX Pro Jr. Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.