Getting a Fresh Fuel Line Onto Your 1987 Yamaha TW200
Shop parts for a 1987 Yamaha TW200 Dirt Bike.
A cracked fuel line seems trivial until it strands you at the far end of a trail or drips onto a hot pipe. On a 1987 Yamaha TW200, the fuel line is a short, inexpensive piece of rubber doing a job with zero tolerance for failure — and replacing it is well within reach with basic hand tools and about half an hour.
Symptoms Worth Catching Early
A fuel line rarely fails without hinting first. Run through this list before loading the TW200 up, particularly if the bike has been sitting.
- Fuel staining at either fitting. Seepage shows up at the barbs before anywhere else.
- Persistent gasoline smell. If you smell fuel with the bike cold and untouched, something is leaking.
- Cracks that appear when you flex the hose. Dry rot hides at rest and reveals itself the moment rubber bends.
- Swelling or a soft, mushy section. The opposite of hardening and just as bad — usually chemical attack.
- Surging or dying under load. Restricted flow mimics fuel starvation and gets misdiagnosed as a jetting problem.
Start by Tracing the Fuel Path
Fuel delivery on the 1987 Yamaha TW200 is carbureted, so the plumbing is about as simple as it gets on a four-stroke dirt bike — tank, petcock, hose, carburetor. That petcock is the most useful thing about this job. Turn it off and the fuel stops, which means no siphoning and no fighting gravity while you work.
Why This Part Wears Out at All
Rubber fuel line fails for reasons that have little to do with how hard you ride. Age drives it: the plasticizers keeping the hose flexible slowly migrate out, and pliable rubber turns stiff and glassy, so a small flex — bolting the tank down, rocking the bike onto a stand — opens a hairline crack. Dry, hot storage accelerates that, pulling volatiles out faster than a temperate garage would. Ethanol-blended pump fuel left sitting in the hose adds a second mechanism, attacking the inner wall and leaving gum that can flake into the fuel path on a 1987 Yamaha TW200.
Tools & Preparation
This is a low-cost job, and most of the preparation is about containing fuel rather than turning wrenches.
- Replacement fuel line in the correct inside diameter and length for your 1987 Yamaha TW200. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
One genuine safety note: gasoline vapor is heavier than air and travels along the floor toward anything that can ignite it. Work outdoors or with the door open, shut off any heater with a pilot light, keep the fuel container capped, and let a hot engine cool first.
Taking the Failed Hose Off
Petcock off, first thing. That valve is why a carbureted bike like the TW200 is forgiving here: shut it and the fuel stops moving.
Capture the fuel sitting downstream. Fit a clear hose to the float bowl drain nipple, run it to your container, and open the drain screw a couple of turns. The bowl empties in under a minute. Close the screw afterward, because a bowl that will not hold fuel is frustrating to diagnose later.
Clamps come next. Squeeze the ears of a spring clamp with pliers and slide it clear, or back off a screw clamp until it moves freely. Then persuade the hose off the barb with a twisting motion rather than a hard yank — old rubber bonds to metal, and a straight pull can bend a carburetor inlet or petcock spigot. When the line is truly seized, slice it lengthwise and peel it away.
Installing the Replacement Hose
Use the removed hose as your measuring stick and cut the new one to match. On a 1987 Yamaha TW200 the correct length stays clear of moving and hot components while still absorbing engine movement without pulling on either fitting. Square off both ends with a sharp blade.
Start at the petcock. Work the hose on until the barb is fully buried — a partial seat is the most common cause of a post-repair leak. Warming a stiff hose helps it slide; lubricating the fitting does not. Leave grease and oil out entirely, since either prevents the rubber gripping properly and can end up inside the carburetor.
Then connect the carburetor side and dry-fit before clamping. Mount the tank if it was removed and verify the hose is not trapped, stretched, or resting on the head. Once the routing looks right, place a clamp at each end over the fitting itself and bring it to snug. New spring clamps are hard to overdo; screw clamps need restraint.
Verifying the Repair
Open the fuel valve and let gravity do the testing. Give the TW200 a few minutes standing over clean cardboard, then inspect the tank-side and carburetor-side joints carefully. Wipe each dry first so new moisture is unmistakable.
Follow that with a running check. Start the engine, bring it to temperature, and look at both fittings again at idle — some leaks only appear once heat and vibration are in the system. A joint weeping under those conditions has a seating problem, not a clamp problem; pull it apart and push the hose fully home.
Then clean up and stay attentive for a ride or two. Dispose of old fuel properly, watch the clamps as the new rubber settles, and consider replacing an inline filter while the system is open. Anyone wanting more detail on what shortens fuel line life long term will find it in our evergreen guide to fuel line care and replacement.
Related Shopping Categories
Shop Fuel Lines for a 1987 Yamaha TW200 Dirt Bike.
Shop Fuel Line Clamps for a 1987 Yamaha TW200 Dirt Bike.
Shop Petcocks for a 1987 Yamaha TW200 Dirt Bike.
Shop Fuel Filters for a 1987 Yamaha TW200 Dirt Bike.
Shop Fuel Stabilizer for a 1987 Yamaha TW200 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.