How to Change the Oil in a 2026 Sherco 250 SE FACTORY

Shop parts for your ride now.

Regular oil changes are crucial for maintaining the performance and longevity of your 2026 Sherco 250 SE FACTORY. This guide provides step-by-step instructions, the tools required, and specific call-outs for this model to ensure you do the job right.

Tools and Supplies Needed

  • 8mm socket
  • 17mm socket
  • 4mm Allen wrench
  • Oil drain pan
  • New engine oil (refer to your manual for type and quantity – typically high-quality motorcycle oil is recommended)
  • New oil filter
  • Replacement aluminum crush washers (for each drain bolt)
  • Funnel
  • Clean rags or paper towels
  • Gloves
  • Torque wrench

Preparation

  • Warm up your bike for a few minutes to thin the oil. This helps it drain more completely.
  • Turn the engine off and ensure the bike is stable on a level stand.
  • Gather all tools and supplies before beginning the oil change.

Step-by-Step Oil Change Instructions

  1. Locate the Drain Plugs:
    • The 2026 Sherco 250 SE FACTORY has two drain bolts on the bottom of the engine.
      Each has an aluminum crush washer that should be inspected and ideally replaced to prevent leaks.
  2. Remove the Drain Plugs:
    • Place the oil drain pan under the engine.
    • Use the 17mm socket to carefully loosen and remove both drain bolts. Allow all oil to drain completely.
    • Inspect the drain bolts–one may have a magnetic tip to catch metal debris. Clean this thoroughly.
  3. Remove and Replace the Oil Filter:
    • Locate the oil filter (consult your manual for precise location if unsure).
    • Use the appropriate tool (usually 8mm socket or 4mm Allen) to remove the cover and the old oil filter.
    • Lubricate the rubber seal on the new oil filter with a small amount of fresh oil, then install the filter.
    • Reattach the filter cover and torque it to manufacturer specifications to avoid damaging the seal or case.
  4. Inspect and Reinstall the Drain Bolts:
    • Inspect the aluminum crush washers. Replace them if they appear deformed or worn.
    • Install the drain bolts by hand, then torque them to the value specified in your owner’s or workshop manual (typically between 10–15Nm, but always verify for your exact model).
  5. Add New Oil:
    • Remove the fill plug, which on the 250 SE FACTORY may be positioned slightly awkwardly under the exhaust header, requiring a steady hand or funnel to avoid spills.
    • Using a funnel, pour in the new recommended oil amount and type for the 2026 Sherco 250 SE FACTORY. Double-check your owner’s manual for the precise specification and volume.
    • Reinstall the fill cap and wipe away any spillage.
  6. Check Oil Level and Leaks:
    • Start the engine and let it run for about a minute.
    • Turn off the engine and wait a couple of minutes for oil to settle.
    • Check the oil level with the dipstick or sight glass and top off if needed.
    • Inspect around the drain bolts and filter area for leaks.
  7. Dispose of Old Oil Properly:
    • Take the used oil and filter to an authorized recycling center. Do not pour old oil down drains or onto the ground.

Model-Specific Call-Outs for the 2026 Sherco 250 SE FACTORY

  • Difficult Fill Port: The oil fill port is located under the titanium exhaust, making access a bit tight. Use a flexible funnel for easier filling and to avoid spills.
  • Two Oil Drain Bolts: Always remove both when draining oil, and check each for the crush washer. Some users choose to replace crush washers at every change, but at minimum, inspect closely for wear.
  • Drain Interval: Many riders err on the side of caution and change oil at 50–65 hours, even though Sherco recommends up to 100 hours for gentle use, especially if you ride in harsh conditions or push the bike hard.
  • Magnetic Drain Plug: Clean any metal debris from the magnetic drain plug each change; excessive shavings can indicate internal wear.
  • Correct Oil Specification: Always consult your owner’s manual for the exact type and quantity recommended for the 2026 model. Sherco specifically calls for high-performance two-stroke oil for the gearbox.

Final Tips

  • Always double check for leaks after your first ride post-oil-change.
  • Keep a log of each service including date, hours/mileage, and the type of oil/filter used for maintenance records and warranty purposes.
  • Do not over-tighten drain bolts or the oil filter cover—use a torque wrench.

Proper oil change technique ensures your 2026 Sherco 250 SE FACTORY stays at peak performance. If you have any doubts or run into difficulty, always consult your local Sherco dealer or qualified mechanic.

This guide is proprietary to MotoSport.com and should not be redistributed without permission.

Related Shopping Categories

Shop Motor Oil for a 2026 Sherco 250 SE FACTORY Dirt Bike.

Shop Oil Filters for a 2026 Sherco 250 SE FACTORY Dirt Bike.

Shop Oil Drain Pans for a 2026 Sherco 250 SE FACTORY Dirt Bike.

Shop Tools for a 2026 Sherco 250 SE FACTORY Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2026 Sherco 250 SE FACTORY Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.