How to change the oil in a 2025 Husqvarna FC350 Dirt Bike

How to Change the Oil in a 2025 Husqvarna FC350

Shop parts for a 2025 Husqvarna FC350 Dirt Bike.

Proprietary to MotoSport.com

Regular oil changes are critical for keeping your 2025 Husqvarna FC350 running at peak performance and extending the engine's life. Follow this robust, step-by-step guide specifically tailored for the 2025 FC350. This procedure closely aligns with prior years’ models, such as the 2022 and 2018 FC350, so experience from those years is applicable, though always check for any year-specific updates.

Tools & Materials Needed

• Drain pan
• 13mm wrench and/or 13mm deep socket
• 8mm socket
• Needle nose pliers
• Torque wrench (0–20 ft-lbs range is sufficient)
• New oil filter (OEM recommended)
• Crush washer replacement (recommended)
• Fresh engine oil (refer to owner’s manual for quantity, typically around 1.1 quarts or 1.0 liter of full-synthetic, 10W-50 or as specified)
• Clean shop rags or paper towels
• Parts cleaning spray (optional but recommended)

Important FC350 Model-Specific Call-outs

• Drain bolt location: The FC350 has a main drain bolt and a separate screen cover bolt that must both be removed for a complete oil change.
• Oil screen removal: Always inspect and clean the oil screen, as it collects debris that could harm your engine.
• Oil filter orientation: Ensure the filter is installed with the correct orientation and that the O-rings are lubricated and in good shape to prevent leaks.
• Proper torque: Do not overtighten drain bolts—follow the specific torque specs for Husqvarna FC350 bolts (typically 14.8 ft-lbs for the drain plug, but confirm with your 2025 manual).
• Oil capacity: The FC350 takes roughly 1.1 quarts of oil; do not overfill.

Step-by-Step Oil Change Process

• 1. Warm up the Bike
  • Start your FC350 and let it idle for 2–3 minutes. Warm oil flows and drains more thoroughly.
  • Turn off the engine and secure the bike on a triangle stand or flat surface.
• 2. Remove the Fill Cap
  • Unscrew the oil fill cap on the right side of the cylinder head. This allows air to enter and oil to flow out faster when draining.
• 3. Drain the Engine Oil
  • Place your drain pan under the bike.
  • Using a 13mm wrench or deep socket, locate and remove the main drain bolt at the bottom of the engine on the left side.
  • Let the oil drain completely.
  • Inspect the crush washer and replace if worn or damaged for a perfect seal.
• 4. Remove and Clean the Oil Screen
  • Locate the oil screen cover bolt (also 13mm). It’s typically near the main drain bolt.
  • After removing the bolt, use needle nose pliers to gently pull the oil screen out.
  • Clean the screen with parts cleaner and inspect for metal shavings. Excessive debris can indicate internal engine issues.
  • Clean the sealing surfaces and O-rings. Replace any O-rings that are flat or damaged.
• 5. Remove and Replace the Oil Filter
  • With an 8mm socket, remove the oil filter cover bolts.
  • Take out the oil filter, noting its orientation.
  • Lightly pre-oil the new filter with clean engine oil.
  • Insert the new filter in the correct direction and reinstall the cover. Ensure the O-ring on the cover is in good condition and properly seated.
• 6. Reassemble the Drain Plug and Oil Screen
  • After the oil has fully drained, wipe any oil residue from the drain hole, install a fresh crush washer, and thread in the drain bolt by hand to avoid cross-threading.
  • Torque the drain bolt to 14.8 ft-lbs (confirm in your 2025 manual if this spec has changed).
  • Lubricate the O-rings on the oil screen with a touch of oil and reinstall it, making sure it sits fully in its groove.
  • Reinstall and torque the oil screen bolt.
• 7. Add New Engine Oil
  • With the bike upright and level, slowly pour in the new oil through the fill port. For the 2025 FC350, use about 1.1 quarts of recommended oil type. Check your manual for Husqvarna’s current oil recommendation.
  • Install the fill cap.
• 8. Check Oil Level
  • Start the engine and idle for 30–60 seconds.
  • Shut off the bike and let it sit for a minute to let oil settle.
  • With the bike standing upright, check the oil level in the sight glass. Add oil a little at a time if necessary—do not overfill.
• 9. Inspect for Leaks
  • Run the engine and check around the drain plug, oil screen, and oil filter cover for leaks.
  • Wipe off any residual oil.
• 10. Dispose of Oil Responsibly
  • Take your used oil and filter to a proper recycling facility—never dump used oil in the trash or the environment.

Tips for the 2025 Husqvarna FC350 Owners

• Do not mix different oil brands/types as per Husqvarna’s recommendation for optimal engine life.
• Check torque on all bolts—overtightening can strip threads in the soft aluminum engine cases.
• Keep records of your oil change intervals for warranty and service.
• If this is your first oil change on a new bike, you might spot extra metal fragments in the oil screen. This is normal, but persistent large amounts may indicate trouble.

Following this guide every 8–10 hours of riding (or as your manual states) will keep your 2025 Husqvarna FC350 running at its best. For more OEM and performance parts or detailed maintenance tips, trust MotoSport.com for all your dirt bike needs.

Related Shopping Categories

Shop Motor Oil for a 2025 Husqvarna FC350 Dirt Bike.

Shop Oil Filters for a 2025 Husqvarna FC350 Dirt Bike.

Shop Oil Drain Pans for a 2025 Husqvarna FC350 Dirt Bike.

Shop Tools for a 2025 Husqvarna FC350 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2025 Husqvarna FC350 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.