How to Change the Oil in a 2024 Sherco 450 SEF FACTORY

Shop parts for a 2024 Sherco 450 SEF FACTORY Dirt Bike.

Changing the oil in your 2024 Sherco 450 SEF FACTORY is a fundamental maintenance task that helps keep your engine running smoothly and extends the life of your bike. At MotoSport.com, we have put together this detailed guide to ensure you complete the oil change correctly and efficiently, with special attention to specifications for the 2024 model year.

Tools & Materials Needed

  • Socket set:– 8mm, 12mm, 17mm sockets
  • 4mm Allen wrench
  • Torque wrench (capable of 15 Nm and 20 Nm adjustments)
  • Oil drain pan
  • Funnel
  • Clean rags or shop towels
  • New oil filter (replace every oil change)
  • New O-rings and crush washers (for drain and filler plugs)
  • SAE 10w60 engine oil (1.1 liters required for 2024 model)
  • Gloves (optional, helps keep hands clean)

Step-by-Step Instructions

  1. Warm Up the Engine
    • Start your motorcycle and let it idle for 2–3 minutes. This allows the oil to heat up, so it drains more easily and carries away impurities.
    • Turn off the engine and place the bike on a stable stand.
  2. Prepare for Drainage
    • Gather your tools and place the drain pan beneath the crankcase. Make sure the area is clean to avoid contamination.
  3. Remove Magnetic Drain Plug
    • Use a 12mm socket or wrench to remove the magnetic drain plug. The plug is located at the bottom of the engine.
    • Allow all oil to drain fully. Inspect the magnetic tip for any metal shavings or debris – if excessive, consult a mechanic.
    • Clean the magnetic drain plug thoroughly and replace the crush washer with a new one every oil change.
  4. Remove the Oil Filter
    • Locate the oil filter cover (usually secured with two or three bolts).
    • Use the correct socket or Allen wrench (typically 8mm or 4mm) to carefully remove the oil filter cover bolts.
    • Remove the old oil filter. Watch for residual oil in the filter cavity. Use a shop towel to carefully wipe out any remaining oil.
    • Install the new oil filter – orientation matters. The open end faces out as depicted in your owner’s manual.
    • Replace the filter cover O-ring if it appears worn, brittle, or damaged.
  5. Reinstall Plugs & Filter Cover
    • Fit the cleaned magnetic drain plug with a new crush washer and torque it to 15 Nm.
    • Reinstall the oil filter cover with a new O-ring and torque the bolts to 15 Nm.
  6. Add Fresh Oil
    • Remove the oil filler cap (usually on the right side of the engine).
    • Using a funnel, add 1.1 liters of SAE 10w60 oil to the engine.
    • Reinstall the filler cap with a new O-ring if needed.
  7. Check the Oil Level
    • Start your bike and let it idle for 1–2 minutes.
    • Shut off the engine and wait 1 minute to allow the oil to settle.
    • Inspect the oil level through the sight glass or by using the dipstick, as instructed in your owner’s manual. Top off if necessary.
  8. Dispose of Old Oil & Filter Responsibly
    • Never pour used oil down the drain or into the environment. Take used oil and the filter to a local recycling center or authorized disposal facility.

Important Call-outs: 2024 Sherco 450 SEF FACTORY

  • Always replace the oil filter with each oil change. The manufacturer states a new filter is imperative every time you service the oil.
  • The required oil capacity for the 2024 model is 1.1 liters of SAE 10w60 oil.
  • The drain plug and oil filter cover torque specs are both 15 Nm.
  • Inspect and replace O-rings and crush washers every service to prevent leaks.
  • Clean the magnetic drain plug and inspect for metal shavings at each change. Significant metal debris may indicate future engine issues.
  • After adding oil and running the bike, always double-check the oil level and adjust as needed for optimal performance and engine protection.
  • The oil change procedure is the same for the 450 SEF Factory and Racing models, as well as similar for model years from at least 2017 through 2024.
“Change engine oil, filter, clean pre filter and change if necessary. Clean the magnetic drain plug. Replace spark plug (after 50 hours). Check and adjust valve clearance (after 50 hours).” – 2024 Owner’s Manual

Regular oil changes are the best protection for your Sherco’s high-performance engine. Always use quality oil, genuine filters, and follow proper torque specifications for complete reliability and maximum fun on every ride.

This guide is proprietary to MotoSport.com and tailored specifically to the 2024 Sherco 450 SEF FACTORY. If you need additional support or the latest OEM parts, visit our site for expert resources and premium service parts.

Related Shopping Categories

Shop Motor Oil for a 2024 Sherco 450 SEF FACTORY Dirt Bike.

Shop Oil Filters for a 2024 Sherco 450 SEF FACTORY Dirt Bike.

Shop Oil Drain Pans for a 2024 Sherco 450 SEF FACTORY Dirt Bike.

Shop Tools for a 2024 Sherco 450 SEF FACTORY Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2024 Sherco 450 SEF FACTORY Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.