How to Change the Oil in a 2024 Kawasaki KLX140R 17/14
Shop parts for a 2024 Kawasaki KLX140R 17/14 Dirt Bike.
Changing the oil in your 2024 Kawasaki KLX140R 17/14 is a straightforward and essential maintenance task that can extend the life of your engine and keep your bike running smoothly. This step-by-step guide is custom-made for MotoSport.com and covers everything you need, including tools, supplies, and 2024 model-specific call-outs.
Tools and Supplies You'll Need
- Ratchet and extension
- 8mm and 17mm sockets
- Drain pan
- Torque wrench
- New oil filter (Kawasaki OEM part number: 52010-1053)
- 10W-40 motorcycle oil (about 1.22 quarts required)
- Replacement crush washer for the drain bolt
- Clean rags
- Gloves (optional but recommended)
Step-by-Step Instructions for Changing the Oil
-
Warm up the engine.
Start the KLX140R and let it run for about a minute. This warms the oil, making it thinner and easier to drain completely.
-
Remove the dipstick.
Unscrew and remove the oil dipstick from the right side of the engine. This vents the crankcase, allowing oil to drain faster and more completely.
-
Position the drain pan.
Slide your drain pan under the bike, positioning it beneath the 17mm drain bolt on the lower left side of the engine.
-
Remove the drain bolt and washer.
Use a 17mm socket and ratchet to remove the drain bolt and the crush washer. Allow all the old oil to drain into the pan. Inspect the washer and replace it if it's worn, deformed, or you notice any leaks in previous oil changes.
-
Replace the oil filter.
The KLX140R uses a cartridge-style oil filter. Using your 8mm socket, remove the three bolts securing the oil filter cover on the right side of the engine. Gently pull the cover off (oil may drip), then remove the old filter and any residual oil inside.
-
Install the new oil filter.
Insert the new filter in the same orientation as the old one. Clean the cover and mating surfaces, check the O-ring for wear (replace if necessary), then reattach the cover and torque the bolts as specified in your owner's manual (do not over-tighten).
-
Reinstall the drain bolt.
Once the oil has finished draining, clean the area around the drain hole. Install the new crush washer, thread in the drain bolt by hand to avoid cross-threading, then torque it to the manufacturer's specification using your torque wrench (consult your service/owner's manual, usually around 22 ft-lbs, but verify).
-
Add new oil.
Place a funnel in the oil fill hole, then pour in 1.22 quarts (1.15 liters) of 10W-40 motorcycle oil. Make sure to use oil specifically formulated for wet-clutch motorcycles.
-
Check oil level.
With the bike level (upright, not on the kickstand), insert the dipstick (do not screw it in), remove it, and check the oil level. Add oil if needed to bring the level up to the full mark. Do not overfill.
-
Start and check for leaks.
Start the engine and let it idle for a minute. Look for any leaks at the drain bolt and oil filter cover. Switch off and recheck the oil level with the dipstick, topping up if necessary.
-
Dispose of old oil and filter responsibly.
Take your used oil and filter to a recycling center or auto parts store that accepts motorcycle oil.
Specific Call-Outs for the 2024 KLX140R 17/14
- As of 2024, the KLX140R maintains the same engine and oil change procedure as models since 2010. Owners of 2024 are advised to follow the same oil capacity and filter requirements as earlier models.
- The drain bolt and oil filter cover are located in the same positions as previous years–no new special tools or extra steps are required for 2024. Use caution not to overtighten bolts to avoid damaging the threads in the aluminum crankcase.
- Kawasaki recommends using 10W-40 oil designed for wet-clutch motorcycles.
- Check that your oil filter O-ring is in good condition during each change to prevent leaks.
- Always reference your owner’s manual for torque specifications and any updates issued by Kawasaki for the 2024 model year. Based on available information, there have been no major changes in the oiling system or procedure for this model year compared to previous years .
Tips for First-Time Oil Changers
- Wear gloves to keep your hands clean and protect against hot oil and sharp edges.
- Work in a well-ventilated area and keep your workspace organized.
- Take your time, especially when reinstalling bolts and components. Stripped threads are a common result of rushing or using the wrong tools.
- If your bike is new (first oil change after break-in), you might see small metal filings in the old oil—this is normal for initial break-in but should lessen over time.
Conclusion
Changing the oil in your Kawasaki KLX140R 17/14 is an essential and manageable DIY job every owner can learn. Regular oil services will keep your dirt bike running strong, ensure maximum engine life, and give you that extra confidence every time you hit the track or trails. For all your parts, oils, and tools, visit MotoSport.com, your trusted Kawasaki experts.
Related Shopping Categories
Shop Motor Oil for a 2024 Kawasaki KLX140R 17/14 Dirt Bike.
Shop Oil Filters for a 2024 Kawasaki KLX140R 17/14 Dirt Bike.
Shop Oil Drain Pans for a 2024 Kawasaki KLX140R 17/14 Dirt Bike.
Shop Tools for a 2024 Kawasaki KLX140R 17/14 Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2024 Kawasaki KLX140R 17/14 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.