How to Change the Oil in a 2024 Husqvarna TE250

Shop parts for a 2024 Husqvarna TE250 Dirt Bike.

Changing the oil in your 2024 Husqvarna TE250 is a crucial maintenance task that ensures your engine runs smoothly and retains performance, especially for enduro riders who routinely put their bikes through tough conditions. This guide, proprietary to MotoSport.com, will walk you through every step, including model-specific notes and tips. Even though the core oil change procedure is similar across recent TE250 models, we’ll call out any unique features or details about the 2024 TE250 that you need to know.

Tools and Supplies Needed

  • Socket set (usually 8mm, 10mm sizes – verify for your year and model)
  • Torque wrench
  • Oil drain pan
  • Replacement oil filter
  • Replacement crush washer for the drain plug
  • Contact cleaner or degreaser
  • Clean rag or shop towels
  • Measuring cup or graduated oil jug
  • Funnel (optional, but helps minimize spills)
  • Recommended engine oil (consult your owner’s manual for viscosity and specifications)
  • Gloves (recommended for cleanliness and safety)

Preparation

  • Start your TE250 and let it idle for 2-3 minutes. This helps thin the oil for a more complete drain. Shut off the engine and place the bike on a stable stand.
  • Remove the skid plate if installed to provide clear access to the drain bolt and oil filter cover.
  • Have all tools and new parts ready before beginning. Confirm the oil filter is compatible with the 2024 TE250; check MotoSport.com for the latest part numbers.

Step-by-Step Oil Change Guide

  • 1. Remove the Oil Fill Cap
    Locate and remove the oil fill cap on top of the engine. This helps the oil drain more efficiently.
  • 2. Position the Drain Pan
    Slide your drain pan beneath the drain plug, typically located at the bottom of the engine.
  • 3. Remove the Drain Plug
    Using an appropriately sized socket, carefully loosen and remove the oil drain plug. Allow the oil to fully drain. Inspect the old crush washer—replace it with a new one to ensure a tight, leak-free seal during reinstallation. The recommended torque spec for the drain plug (always check your owner's manual for current figures) should be followed on reinstallation.
    Note: On the TE250, Husqvarna recommends draining oil while the engine is warm for best results.
  • 4. Remove the Oil Filter Cover & Filter
    Using the correct socket (usually 8mm or 10mm), undo the bolts securing the oil filter cover. Remove the oil filter and note the position of any springs present. On some TE250s, there is a spring between the filter and engine – ensure it is seated properly during reassembly.
    Model-specific tip: Owners of recent TE models (including 2024) should watch for a small spring located behind the filter. When removing the cover, make sure this spring goes back in FIRST, followed by the filter, then the cover.
  • 5. Inspect and Clean Components
    Use a rag and some contact cleaner to wipe away any residual oil from the filter cavity, cover, and drain bolt. Check for any debris in the used oil or filter that could signal internal engine wear.
  • 6. Install the New Oil Filter
    Place the spring (if present) in the correct orientation, then seat the new oil filter in place. Refit the filter cover and torque bolts to the value specified in your service manual.
  • 7. Reinstall the Drain Plug
    Fit a new crush washer onto the drain plug, reinstall, and tighten with a torque wrench to the specified value. Overtightening can strip threads; undertightening can cause leaks, so always use a torque wrench if possible.
  • 8. Add New Oil
    Using a funnel, pour the recommended amount and type of engine oil into the fill port. The 2024 TE250 typically requires approximately 0.80 to 0.85 liters, but always verify for your exact sub-model in the manual. Some versions may vary slightly due to changes in engine casting or clutch components.
    Only use oils that meet Husqvarna’s requirements for your performance and warranty protection.
  • 9. Check Oil Level
    Replace the oil fill cap and start the engine. Let it idle for 1–2 minutes, then shut off and allow it to sit for a minute. Use the inspection window or dipstick (depending on TE250 sub-model) to verify the oil is at the correct level. Top off as necessary.
  • 10. Inspect for Leaks
    With the bike running, inspect around the filter cover, drain plug, and banjo bolts for oil leaks. Remedy any leaks before riding.
  • 11. Record the Service
    Document oil change date, hours, and oil type in your maintenance log. For enduro riding, Husqvarna recommends changing the oil at least every 15 hours or sooner for severe conditions.

2024 TE250 Model-Specific Call-Outs

  • The oil change process and hardware are broadly consistent with TE250 models from 2023–2024. However, always double-check oil capacity and torque values published in your specific owner's manual, as minor manufacturing changes may influence these figures.
  • Changing the oil filter with each change is highly recommended for the 2024 TE250 to maximize engine protection.
  • Keep an eye out for the small spring behind the oil filter in the filter housing and refit it correctly on reassembly—failure to do so can reduce oil flow and engine life.

Pro Tips for Your TE250 Oil Change

  • If the used oil looks abnormally dark, gritty, or milky, investigate further before returning to aggressive riding. Unusual oil can be a sign of water ingress or internal wear.
  • Consider changing your crush washer at every oil change, as these are a common source of post-service leaks if reused.
  • Never overfill the engine with oil, as this can cause excessive crankcase pressure and leaks.

Resources and Service Information

  • The official 2024 TE250 owner’s and service manuals are available in PDF at Husqvarna’s website. They contain diagrams, exact torque specs, and part numbers for reference.

Performing your own oil changes keeps your 2024 Husqvarna TE250 in top condition and ensures each ride is smooth, safe, and reliable. All service parts are available at MotoSport.com—check for year-specific oil filters, crush washers, and recommended oil for your Husky.

Related Shopping Categories

Shop Motor Oil for a 2024 Husqvarna TE250 Dirt Bike.

Shop Oil Filters for a 2024 Husqvarna TE250 Dirt Bike.

Shop Oil Drain Pans for a 2024 Husqvarna TE250 Dirt Bike.

Shop Tools for a 2024 Husqvarna TE250 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2024 Husqvarna TE250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.