How to Change the Oil in a 2024 Husqvarna TE150: A MotoSport.com Proprietary Guide
Shop parts for a 2024 Husqvarna TE150 Dirt Bike.
Regular oil changes are crucial for keeping your 2024 Husqvarna TE150 in peak condition and ensuring the longevity of your transmission and clutch components. This detailed guide covers every step, tool needed, and unique considerations for your specific make and model, so you can ride with confidence knowing your machine is expertly maintained.
Tools and Supplies Needed
- 10mm socket or wrench (for drain and level bolts)
- Torque wrench (for precise reinstallation of drain bolts)
- Oil drain pan
- Funnel
- Rags and contact cleaner (for cleanup)
- Measuring cup (to ensure correct oil quantity)
- 10W-40 transmission oil (check your manual for specification – 10W-40 is the typical recommendation)
- New crush washers (recommended, but not strictly required for each change)
- Gloves (optional, to keep hands clean)
Model-Specific Call-Outs for the 2024 Husqvarna TE150
- Two drain bolts: This model, like other recent TE150s, has two drain bolts, one on each side of the transmission case. Both should be removed to fully drain the oil.
Note: One bolt contains a magnetic tip to catch debris – inspect and clean it when draining the oil. - Oil level check bolt: The bike has an oil level check screw above the starter. This must be removed to properly verify the oil fill level.
- Recommended oil: Use high-quality 10W-40 transmission oil. Using the correct oil type preserves clutch feel and gearbox life.
- Warm the bike up: Always bring the engine to operating temperature before draining. Warm oil drains faster and more completely.
Step-by-Step Oil Change Procedure
-
Prep the bike:
- Start and run your Husqvarna TE150 for several minutes to warm the oil.
- Shut off the engine. Place the bike upright using a stand for stability.
- Gather all tools and position the oil drain pan beneath the transmission case, covering both sides where the drain bolts are located.
-
Remove the drain bolts:
- Use the 10mm socket or wrench to loosen and remove the first drain bolt (magnetic) on the left side of the case.
- Allow the oil to begin draining, then remove the second drain bolt on the other side to ensure all oil is evacuated.
Tip: Tilting the bike slightly from side to side can help remove any stubborn oil pockets. - Carefully inspect and clean the magnetic tip for metal shavings. Replace any crush washers if they appear damaged or flattened.
-
Reinstall drain bolts:
- Thread both drain bolts back into place by hand to avoid cross-threading.
- Use a torque wrench to tighten bolts to the manufacturer—s specified torque rating (check your owner—s manual for exact values; typically around 10 Nm for steel bolts).
-
Refill with fresh oil:
- Locate and remove the oil fill cap (usually situated on the right side of the engine).
- Carefully pour in the recommended amount of 10W-40 transmission oil using a measured cup and funnel. For the TE150, check your manual for specific capacity (commonly around 700ml, but always verify).
- Do not overfill – you'll finalize the exact amount using the level check step.
-
Check the oil level:
- With the bike level and upright, locate the oil level check screw above the starter.
- Remove the screw. Oil should begin to trickle out slowly – this confirms you are at the correct level. If not, add oil slowly in small increments until oil just seeps through the check hole.
Tip: Always check the level with the bike perfectly upright, not on its side stand. - Reinstall the oil level check screw securely once verified.
-
Final steps:
- Reinstall the oil fill cap, ensuring it is snug.
- Wipe off any oil residue with rags and clean the area with contact cleaner to prevent dirt buildup.
- Start the bike and let it run briefly. Check for leaks around the drain bolts and fill/level areas.
- Dispose of old oil responsibly at a certified recycling facility.
Additional Husqvarna TE150 Oil Change Tips
- Change interval: Oil and filter should be changed every 10–15 hours of riding for typical off-road use. More frequent changes (as low as every 3 hours) may be necessary for racing or extreme conditions.
Note: Frequent transmission oil changes protect clutch plates and gearbox under heavy use.
Reference: Some owners change as often as every 3 hours, while factory guidelines tend to be more conservative for casual riders. - Inspect for contamination: Routine checks of old oil and magnetic drain plugs help identify early signs of excessive wear or mechanical issues.
- Never substitute engine oil for transmission oil. Use only oils rated for gearboxes and wet clutches to avoid slippage and ensure correct protection.
- Stay organized: Keep track of oil changes using a maintenance log. This helps resale value and keeps your Husqvarna running strong.
Conclusion
The 2024 Husqvarna TE150 makes oil changes straightforward with its dual-drain design and dedicated check bolt. Following this step-by-step MotoSport.com guide and always consulting your owner's manual for specifications will help protect your investment and keep you riding with confidence for seasons to come.
Related Shopping Categories
Shop Motor Oil for a 2024 Husqvarna TE150 Dirt Bike.
Shop Oil Filters for a 2024 Husqvarna TE150 Dirt Bike.
Shop Oil Drain Pans for a 2024 Husqvarna TE150 Dirt Bike.
Shop Tools for a 2024 Husqvarna TE150 Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2024 Husqvarna TE150 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.