How to Change the Oil in a 2024 Husqvarna FE501W – MotoSport.com’s Complete Guide

Shop parts for a 2024 Husqvarna FE501W Dirt Bike.

Your 2024 Husqvarna FE501W is built for performance and reliability, but regular oil changes are key to keeping that engine running smooth. Here’s MotoSport.com’s proprietary, step-by-step process—including specific tools you’ll need, thorough instructions, and important call-outs for the newest FE501W model.

Tools & Supplies Needed

  • 8 mm socket (¼" drive)
  • 13 mm socket (¼" & ½" drive)
  • Torque wrench (range: 11–15 ft-lb)
  • Fresh oil (Motorex SAE 10W-50 recommended, approximately 1.3 quarts)
  • OEM oil filter
  • OEM copper crush washers/gaskets (recommended for each oil change)
  • Oil drain pan
  • Funnel
  • Snap-ring pliers (for oil filter removal)
  • Flathead screwdriver (to align oil screen, if needed)
  • Gloves, rags or shop towels
  • Contact cleaner or degreaser
  • Service manual pages 131–133 (for reference & torque specs)

Step-by-Step Oil Change for the Husqvarna FE501W (2024)

  1. Warm Up the Engine
    Start the bike and let it idle for about 2–3 minutes—just until it reaches normal operating temperature.
    This thins the oil so it drains faster and more completely.
  2. Remove the Skid Plate
    If your model has a skid plate, loosen the mounting bolts and remove it to access the drain plugs easily.
    Clean off major dirt/grit around the work area before starting to avoid contaminating the engine during reassembly.
  3. Clean Around Drain Plugs & Parts
    Use contact cleaner to spray the area around the drain bolts and oil filter cover to prevent dirt from falling into the crankcase during removal.
  4. Place Oil Drain Pan
    Position a suitable drain pan under both crankcase drain bolts.
  5. Remove the Drain Bolts
    • There are typically two 13 mm drain bolts on the FE501W.
    • One is just under the shifter—the primary drain. The other (with a built-in magnet) is slightly farther back.
    • Have your crush washers ready. Remove both, allowing oil to pour out completely.
    • Model-Specific Note: The FE501W uses a removable oil screen behind the left-side drain bolt. If the screen doesn’t come out with the bolt, carefully extract it using a screwdriver. Clean the screen, replace if damaged, and reinstall.
  6. Remove and Inspect the Oil Filter
    • Use snap-ring pliers to remove the oil filter cover. Pull out the old oil filter.
    • Check the filter for metal particles or unusual contamination (a normal part of first few changes, but concerning if consistent).
    • Clean the housing, replace with the new filter, and ensure it’s seated correctly.
  7. Let Oil Completely Drain
    Allow several minutes for all oil to drain—including what may drip from the oil filter housing and screen ports.
  8. Replace Drain Bolts & Install New Washers
    • Install fresh copper crush washers on both bolts.
    • Reinstall both drain bolts by hand to avoid cross-threading, then torque:
    • Main drain bolt: 11 ft-lb (check manual for confirmation)
    • Magnet drain bolt (if present): 15 ft-lb
  9. Refit Oil Filter Cover
    • Reinstall the filter cover, ensuring O-rings are clean and not pinched. Torque to manufacturer specs.
  10. Add Fresh Oil
    • Using a funnel, add just under 1.3 quarts (or 1.2L) of Motorex 10W-50, or oil type specified in your service manual.
    • Replace the filler cap.
  11. Start and Circulate Oil
    • Run the engine for 1–2 minutes, then shut off and let oil settle.
    • Check for leaks at both drain bolts and filter cover.
    • Inspect oil level at the sight glass—oil should be at the midpoint.
    • Add oil in small amounts if needed, but do not overfill.
  12. Reinstall the Skid Plate
    • Clean and reinstall after ensuring there are no leaks.
  13. Dispose of Used Oil Responsibly
    Take your used oil and filter to a recycling center, or check with your local MotoSport for disposal locations.

Special Call-Outs for the 2024 Husqvarna FE501W

  • First Oil Change: Husqvarna recommends the first oil change at 1 hour of operation for new break-in, then at regular intervals as specified in the owner’s manual.
  • Oil Screen Inspection: Always extract, inspect, and clean the oil screen during each change. Replace it every 2–3 changes for best results.
  • Use Only OEM or Spec Oil Filters & Gaskets: The high-performance single-cylinder FE501W engine depends on proper oil flow and filtration for longevity.
  • Torque Matters: Do not overtighten drain bolts—aluminum threads can easily be stripped. Use a quality torque wrench for all critical fasteners.
  • Stay Clean: Meticulously clean the work area and components before beginning, especially if the bike was ridden off-road prior to service.

For OEM parts, recommended oils, and bolt kits visit MotoSport.com for everything you need to keep your 2024 Husqvarna FE501W factory-fresh and ready for your next ride. Following these steps will ensure a long, healthy life for your engine and years of reliable performance.

Related Shopping Categories

Shop Motor Oil for a 2024 Husqvarna FE501W Dirt Bike.

Shop Oil Filters for a 2024 Husqvarna FE501W Dirt Bike.

Shop Oil Drain Pans for a 2024 Husqvarna FE501W Dirt Bike.

Shop Tools for a 2024 Husqvarna FE501W Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2024 Husqvarna FE501W Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.