How to Change the Oil in a 2024 Husqvarna FE350W

Shop parts for a 2024 Husqvarna FE350W Dirt Bike.

Changing the oil on your 2024 Husqvarna FE350W is a crucial maintenance task that helps extend engine life and keep your dirt bike performing at its best. Follow this comprehensive guide, proprietary to MotoSport.com, to safely and efficiently change your oil, including specific pointers for this particular make and model.

Tools and Supplies Needed

  • 8mm socket or Torx T30 bit (for skid plate removal)
  • 13mm socket or wrench (for drain plug)
  • Drain pan
  • Oil filter removal tool (if available - recommended but not critical)
  • Replacement oil filter
  • Replacement engine oil (consult your owner's manual; Husqvarna typically recommends a high-quality 4-stroke motorcycle oil)
  • New drain plug crush washer (copper)
  • Clean rags or shop towels
  • Safety gloves
  • Adequate workspace (well-ventilated and stable surface)
  • Torque wrench (optional, for proper bolt torque)

Preparation and Safety

  • Run your engine briefly (1-2 minutes) to warm the oil for easier drainage.
  • Turn off your bike and place it securely on a stand or have someone steady it.
  • Allow the engine to cool slightly, but not completely, to avoid burns.

Step-by-Step Instructions

  1. Remove the Skid Plate:
    • Use the 8mm socket or T30 Torx bit to undo the bolts holding the skid plate in place.
    • Some aftermarket skid plates may need to be fully removed; stock skid plates may tilt down without full removal (for best access, remove it completely) .
    • Set the skid plate aside and clean any oil or debris from it.
  2. Locate and Remove the Oil Drain Plug:
    • The 2024 FE350W uses a magnetic sump plug at the rear of the engine–a 13mm bolt with a copper crush washer .
    • CAUTION: There are several Allen-head plugs underneath; do not remove these, as they are not for oil draining . Removing the wrong plug can cause damage or release internal components.
    • Place your drain pan under the plug and carefully remove it.
  3. Drain the Oil:
    • Allow the oil to fully drain; tilting the bike gently can help evacuate all old oil.
    • Check the magnet on the drain plug for metal particles; a small amount is typical, but lots of shavings may indicate a problem

      .
  4. Remove and Clean the Oil Screen:
    • Locate the oil screen plug (see your owner's manual for exact location; usually near the drain plug).
    • Remove the oil screen and clean it with brake cleaner or solvent. Inspect for debris or metal shavings

      .
  5. Replace the Oil Filter:
    • Remove the oil filter cover bolts and carefully remove the old oil filter (note its orientation).
    • Install a new filter, ensuring the correct direction–usually the open end faces outward, but check your service manual or the markings.
    • Inspect and replace any O-rings if damaged or flattened

      .
    • Reinstall the filter cover and tighten bolts evenly.
  6. Reinstall Drain Plug and Oil Screen:
    • Install the freshly cleaned oil screen.
    • Replace the crush washer on the drain plug. Tighten to the manufacturer's recommended torque spec (typically 15-20 Nm; always check your manual)

      .
  7. Add New Engine Oil:
    • Locate your oil fill cap and remove it.
    • Using a clean funnel, pour in the recommended amount and grade of oil (see manual; generally around 1.2 liters for the FE350W).
    • Replace the oil fill cap.
  8. Check for Leaks and Final Steps:
    • Start the engine and let it idle for a minute. Watch the drain plug, filter, and cover area for leaks.
    • Turn off the engine. Wait a few minutes, then check the oil level and top off if necessary.
    • Reinstall your cleaned skid plate.
  9. Dispose of Old Oil Properly:
    • Collect old oil in a sealed container and take it to an authorized recycling center or auto parts store. Never pour oil down drains or onto the ground.

2024 Husqvarna FE350W Specific Call-outs

  • Do NOT confuse the Allen-head plugs on the engine bottom with the oil drain plug; removing the wrong plugs can cause mechanical damage .
  • This model has a magnetic drain plug and an oil screen. Both should be removed and cleaned during every oil change.
  • The oil filter cover bolts and oil screen cover have O-rings that should be inspected and replaced if damaged for a proper seal .
  • Always use a copper crush washer on the drain plug to prevent leaks and replace with each oil change.

Pro Tips for FE350W Owners

  • Tilt your bike from side to side gently after draining to ensure complete oil removal.
  • Clean the magnetic tip of the drain plug thoroughly to monitor engine wear.
  • Check for leaks after your first short ride post-oil change as some seals may shift with heat.
  • If you're new to servicing your bike, have your owner's manual handy for extra torque specs and capacity information.

Performing regular oil changes on your 2024 Husqvarna FE350W will keep your dirt bike in peak condition, ready for your next adventure. For more OEM and aftermarket parts, service items, and riding tips, trust MotoSport.com—your partner in every ride.

Related Shopping Categories

Shop Motor Oil for a 2024 Husqvarna FE350W Dirt Bike.

Shop Oil Filters for a 2024 Husqvarna FE350W Dirt Bike.

Shop Oil Drain Pans for a 2024 Husqvarna FE350W Dirt Bike.

Shop Tools for a 2024 Husqvarna FE350W Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2024 Husqvarna FE350W Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.