How to Change the Oil in a 2024 GAS GAS MC 250

Shop parts for a 2024 GAS GAS MC 250 Dirt Bike.

Changing the oil in your 2024 GAS GAS MC 250 is a crucial maintenance task for protecting your engine and ensuring optimal performance. Below, you'll find a detailed guide that includes the tools you'll need, a step-by-step walkthrough, and important tips specific to the 2024 MC 250. This guide is proprietary to MotoSport.com.

Tools & Materials Needed

  • Oil filter (new replacement)
  • Engine oil (consult owner's manual for quantity and specification)
  • Drain pan
  • Rags or shop towels
  • 8mm T-wrench
  • 8mm Allen wrench
  • 13mm ratchet or socket
  • Crush washer (replacement recommended)
  • Needle nose pliers (for oil screen if needed)
  • Optional: torque wrench (recommended for reinstalling drain bolt)
  • Bike stand (recommend an open cradle stand rather than a solid platform under the sump, see notes below)

Key Notes for the GAS GAS MC 250 (2024)

  • Stand choice matters:– Use an open or side stand for access to the drain bolt. The traditional flat stand can block access, making removal difficult and messy. Leaning the bike slightly also helps with thorough drainage of old oil.
    Pro tip: Avoid a solid stand directly under the sump for this model.
  • Check O-rings and crush washers:– Inspect and replace worn or damaged sealing surfaces for both the oil filter cap and the drain bolt to assure a leak-free seal.
  • Oil screen cleaning:– When removing the oil screen, carefully inspect for metal debris. Metal shavings can signal internal engine wear.
  • Tightening torque:– The oil drain plug should be tightened to 14.8 ft-lbs for proper sealing and to avoid stripping threads.

Step-by-Step Oil Change Instructions

  1. Warm up the engine:– Let your bike idle for 3-5 minutes. This warms the oil, helping it drain completely along with contaminants.
  2. Secure the bike on a suitable stand:– Make sure you use an open cradle stand as referenced above. Avoid stands that block the drain bolt area.
  3. Remove the skid plate (if equipped):– This step may be needed for full access to the drain bolt and oil filter.
  4. Place a drain pan beneath the engine's oil drain plug.
  5. Remove the drain plug:– Use a 13mm ratchet or socket to remove the plug. Let the oil drain completely.
    Tip: Slightly lean the bike to the side to help drain all the oil.
  6. Remove the oil filter:– Using an 8mm T-wrench, remove the two bolts holding the oil filter cover. Pull out the old oil filter. Needle nose pliers can help if it is stuck.
  7. Inspect and clean:–
    • Wipe the oil filter cavity and cap clean.
    • Check the O-ring on the filter cover. Replace if it is flattened, cracked, or damaged.
    • If your model has an oil screen, pull it out with pliers, clean it thoroughly, and examine for metal shavings. Replace or reinstall as needed.
  8. Replace the oil filter:– Install the new oil filter, ensuring correct orientation (spring-side out, if applicable).
  9. Replace the drain plug:–
    • Install a new crush washer on the drain plug to prevent leaks.
    • Hand thread the drain plug back in, then tighten to 14.8 ft-lbs with a torque wrench for proper sealing.
  10. Reinstall the oil filter cap:– Ensure the O-ring is in good condition and seated properly, then secure the cap with its two bolts using the 8mm T-wrench.
  11. Add new oil:–
    • Remove the oil fill cap.
    • Pour in the correct type and amount of oil (see your owner's manual for capacity and specification; typically in the –1 liter range for MC 250 four-strokes).
    • Reinstall the cap.
  12. Check for leaks:– Start the motorcycle, let it idle for 1-2 minutes, and check around the drain bolt and oil filter cap for any leaks. Shut off the engine, wait a minute, and re-check oil level. Top off if needed.
  13. Properly dispose of old oil and filter:– Handle used engine oil and the filter according to local environmental regulations; most auto parts stores will accept used oil for recycling.

Additional Tips Specific to the 2024 GAS GAS MC 250

  • Always double-check the oil level after your first short ride post-change. New filters sometimes absorb more oil after initial use.
  • Inspect old oil for contaminants – heavy metallic flakes can indicate wear and need attention from a professional mechanic.
  • For riders in sandy or wet conditions, change the oil more frequently as extra debris and moisture can contaminate engine oil faster.
  • Always use the recommended oil viscosity and specification as outlined in your owner's manual.

Conclusion

Completing regular oil changes is the cornerstone of reliable performance for your 2024 GAS GAS MC 250. Using the correct tools and following the steps above will help keep your bike in top condition and ready for the next ride. For all your oil, filters, and maintenance supplies, trust MotoSport.com for factory-recommended products and fast shipping.

Related Shopping Categories

Shop Motor Oil for a 2024 GAS GAS MC 250 Dirt Bike.

Shop Oil Filters for a 2024 GAS GAS MC 250 Dirt Bike.

Shop Oil Drain Pans for a 2024 GAS GAS MC 250 Dirt Bike.

Shop Tools for a 2024 GAS GAS MC 250 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2024 GAS GAS MC 250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.