How to Change the Oil in a 2022 Husqvarna TE250i: A Complete Guide
Shop parts for a 2022 Husqvarna TE250i Dirt Bike.
This proprietary MotoSport.com guide walks you through a robust process for changing the transmission (gear) oil in your 2022 Husqvarna TE250i. Proper oil changes are crucial for performance and longevity, especially in high-performing enduro bikes like the TE250i. This article will detail the required tools, the step-by-step process, and specific tips for the 2022 model, so you can keep your bike in top shape and avoid costly repairs.
Tools and Supplies Needed
- 8mm socket and ratchet (or a stubby wrench) – for removing and reinstalling the drain plug and guards
- Extension bar – helpful for tight access areas
- Drain pan – to catch old oil
- Funnel – for easier refilling
- Replacement gear oil – Husqvarna recommends 10W-50 or a manufacturer-approved equivalent
- New crush washer – essential for preventing leaks (replace every oil change)
- Clean rags or shop towels – for cleanup
- Torque wrench – to tighten bolts to spec
- Safety gloves (optional) – for skin protection
Pre-Change Tips & Model-Specific Call-Outs
- The 2022 TE250i uses a separate gear oil system; there is no engine oil as it is a two-stroke with fuel-injection.
- The oil fill and level check bolt is located on the right side, marked "OIL". You do not need to remove the rear brake pedal or spring for access; a stubby 8mm wrench works well in the tight space.
- Always change the crush washer to prevent leaks. Retorquing with an old washer can cause seeping.
Step-by-Step Process
- Warm Up the Engine (Optional)
- Start the bike and let it idle for 2–3 minutes. This thins the oil for a more effective drain. Shut off and wait until the bike is safe to touch.
- Position the Bike
- Stabilize the bike on a stand or level ground. Ensure it’s upright—a center stand lifts are safest.
- Remove the Skid Plate/Guard
- Use an 8mm socket and remove the two bolts securing the skid plate or plastic engine guard beneath the bike. Swing the guard down or remove it for access to the drain bolt.
- Drain the Old Oil
- Place your drain pan below the oil drain bolt (on the bottom-left of the engine case).
- Using an 8mm socket with extension if necessary, loosen and remove the drain bolt. Old oil will flow out—inspect for any metal shavings.
- Let the oil drain completely (about 5–10 minutes).
- Care for the Drain Bolt and Washer
- Thoroughly clean the drain bolt. Replace the crush washer with a new one to prevent leaks.
- If equipped with a magnet, inspect it for metal debris (a small amount is normal).
- Reinstall the Drain Bolt
- Thread the drain bolt in by hand, then torque it to manufacturer spec (typically around 15 Nm or about 11 ft-lb).
- Fill with New Gear Oil
- Locate the oil fill bolt (upper right side, marked "OIL"). Remove with an 8mm socket or stubby wrench.
- Using a funnel, add 0.80 liters (0.85 quarts) of approved oil. Pour slowly to avoid overfilling.
- Check Oil Level
- With the bike upright, oil should just begin to seep from the level check bolt hole when properly filled.
- Reinstall and snug the oil check/fill bolt by hand, then tighten with wrench (do not overtighten).
- Reinstall the Skid Plate/Guard
- Refit the skid plate or plastic guard with its bolts; ensure they’re tight but not overtightened.
- Cleanup and Final Inspection
- Wipe all oil residue. Start the bike and check for leaks at the drain and fill/level bolts.
- Dispose of old oil safely at a designated recycling location.
Additional Tips and Model-Specific Details
- No need to remove the brake pedal or shift lever for access—an 8mm stubby or even 3/8" drive fits in the space easily.
- Use the oil specified by Husqvarna or equivalent to maintain warranty and optimal clutch performance.
- Frequent changes (every 10–15 hours of riding or after races) are recommended for best longevity.
- Always check the condition of O-rings on oil screen or caps if removed. Replace if cracked or flattened.
Changing the oil on your TE250i is straightforward and, with regular attention, helps prevent costly transmission or clutch damage. If you need tools, genuine oil, or replacement parts, MotoSport.com has everything you need to complete the job right.
Related Shopping Categories
Shop Motor Oil for a 2022 Husqvarna TE250i Dirt Bike.
Shop Oil Filters for a 2022 Husqvarna TE250i Dirt Bike.
Shop Oil Drain Pans for a 2022 Husqvarna TE250i Dirt Bike.
Shop Tools for a 2022 Husqvarna TE250i Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2022 Husqvarna TE250i Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.