How to Change the Oil in a 2022 Husqvarna FE501S

Shop parts for a 2022 Husqvarna FE501S Dirt Bike.

Regularly changing the oil in your 2022 Husqvarna FE501S is key to keeping its high-performance engine running smoothly and reliably—especially if you ride aggressively or in tough conditions. This guide, proprietary to MotoSport.com, walks you through each step, highlighting the specific nuances of this model. Follow along for a robust, expert-level oil change you can do at home.

Tools and Supplies Needed

  • 8 mm and 13 mm sockets (1/4" and 3/8" ratchets)
  • Torque wrenches (capable of measuring 11 ft-lb and 15 ft-lb)
  • Oil drain pan
  • Funnel
  • Measuring cup (to measure ~1.3 quarts / 1.2 liters of oil)
  • Fresh oil (Motorex SAE 10W-50 recommended for 2022 FE501S)
  • Factory spec oil filter
  • Copper crush washer (for drain bolt)
  • Screwdriver (for filter cover)
  • Outside snap ring pliers (to assist with oil filter removal if needed)
  • Rags/towels (for cleanup)
  • Contact cleaner (for cleaning bolt and filter surfaces)
  • Service manual pages 131-133 (optional, provides torque specs and illustrations)

Note: Always wear gloves, safety glasses, and ensure your workspace is clean and well-ventilated.

Step-by-Step Oil Change Process

  1. Warm Up the Engine
    Start your bike and let the engine idle for a few minutes. This will help the oil drain thoroughly by thinning it out.
    Caution: Warm oil flows better, but be careful—engine parts will be hot.
  2. Remove Skid Plate (if equipped)
    Using the correct socket, remove your skid plate to access the bottom of the engine.
    This is essential on most FE501S models to reach the drain plugs easily.
  3. Place the Oil Pan
    Position an oil drain pan directly under the engine’s drain plug.
  4. Remove the Main Oil Drain Plug
    Use a 13 mm socket to loosen and remove the main drain bolt. Allow the oil to drain fully.
    Replace the copper crush washer if it's deformed or worn.
  5. Remove and Clean Oil Screen & Filter Screws
    - Remove the long and short oil filter screws from the right crankcase cover.
    - Carefully remove the oil filter cover with a screwdriver.
    - If needed, use snap ring pliers to help remove the filter.
    - Inspect and clean the mesh filter and all screws. Clean mating and sealing surfaces with contact cleaner.
  6. Replace Oil Filter
    - Install a new factory-spec oil filter. - Lubricate the rubber O-ring on the oil filter cover with some fresh oil before reinstalling.
    - Insert the new filter into position and reinstall the cover. - Torque the cover screws to specification (consult manual for exact torque, typically around 11 ft-lb).
  7. Reinstall and Torque Bolts Properly
    - Install the cleaned or new main oil drain plug with new copper washer. - Torque the drain plug and filter cover bolts to their specified values (drain: approx. 11-15 ft-lb, filter cover: 11 ft-lb).
  8. Add Fresh Oil
    - Using a funnel, pour in 1.2 liters (1.3 US quarts) of Motorex SAE 10W-50 oil. - Go slow to avoid spills, and let the oil settle.
  9. Check Oil Level
    - Fire up the bike for one minute, shut it down, and let it sit for one minute so the oil can drain into the sump.
    - Check the oil sight glass or dipstick and top off if needed.
  10. Reinstall Skid Plate
    Reattach the skid plate securely.
  11. Inspect for Leaks and Clean Up
    - Start the engine and check for leaks at the drain plug and oil filter cover. - Dispose of your used oil and filter at a proper recycling center.

2022 FE501S Model-Specific Notes and Call-Outs

  • Two Oil Filters or Screens: The 2022 FE501S uses both a cartridge filter and two mesh oil screens that must be cleaned during each oil change.
  • Drain Bolt Placement: Be aware of two different drain bolts (main and mesh/auxiliary). Ensure you remove and clean both for a thorough oil change.
  • Tight Spaces: The skid plate may make access difficult, so careful removal and reinstallation is recommended to prevent cross-threading.
  • Oil Quantity: Don’t overfill. The engine takes about 1.2 liters, but use the sight glass as your final reference.
  • First Oil Change Reminder: Husqvarna recommends the first oil change at just one engine hour for new bikes—check your hour meter if it’s your first service.
  • Gasket & O-Rings: Always replace the copper crush washer on the drain plug and check the oil filter cover O-ring for damage.

Final Tips

  • Keep notes for your records (mileage, date, oil brand, filter brand).
  • Use only premium motorcycle-specific oils and filters.
  • Always dispose of used oil responsibly and legally.
  • Consult your official service manual for any updated torque specs or procedures as the 2022 FE501S may differ slightly from previous years.

Changing your own oil isn’t just maintenance–it’s preventive care that maximizes the life and power of your Husqvarna FE501S. MotoSport.com is your source for everything you need, from filters to crush washers and Motorex oil, empowering you for every ride.

Related Shopping Categories

Shop Motor Oil for a 2022 Husqvarna FE501S Dirt Bike.

Shop Oil Filters for a 2022 Husqvarna FE501S Dirt Bike.

Shop Oil Drain Pans for a 2022 Husqvarna FE501S Dirt Bike.

Shop Tools for a 2022 Husqvarna FE501S Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2022 Husqvarna FE501S Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.