How to Change the Oil in a 2019 Sherco 300 SE Factory

Shop parts for a 2019 Sherco 300 SE Factory Dirt Bike.

Changing the oil in your 2019 Sherco 300 SE Factory is a routine maintenance task that ensures the longevity and performance of your motorcycle. Here's a step-by-step guide to help you accomplish this task efficiently.

Tools Needed:

  • Socket wrench or ratchet set with appropriate sockets (e.g., 17mm, 8mm)
  • 4mm Allen head tool
  • Drain pan or container
  • Funnel
  • New oil filter (if applicable)
  • SAE 10W60 motor oil (0.9L)
  • Gaskets or crush washers for drain plugs
  • Thread locker (optional)

Step-by-Step Instructions:

1. Prepare the Bike:
– Ensure the motorcycle is parked on a level surface and the engine is warm.
– Place a drain pan or container under the bike to catch the old oil.

2. Remove the Drain Plugs:
– Use a 17mm socket to remove the main drain plug located at the bottom of the engine.
– Some models may have a second drain plug, so refer to your manual for specific instructions.
– Use a 4mm Allen head for any additional bolt heads if present, such as the pre-filter or oil centrifuge related bolts.

3. Drain the Oil:
– Allow the oil to drain completely before proceeding.

4. Replace the Drain Plugs:
– Once the oil has stopped dripping, replace the drain plugs and tighten them securely.
– Ensure you use new gaskets or crush washers each time to prevent leaks.

5. Replace the Oil Filter (if applicable):
– Although the oil filter is not mentioned for the 2019 Sherco 300 SE Factory, if you have an oil filter, replace it with a new one and install it in the correct direction.

6. Refill the Oil:
– Use a funnel to pour in the new oil. The recommended oil type is SAE 10W60, and the capacity is approximately 0.9L.
– Consult your manual for any updates or adjustments to this specification.

7. Check the Oil Level:
– After refilling, start the engine and let it run for a few minutes to circulate the new oil.
– Turn off the engine and check the oil level using the sight glass. Add more oil if necessary.

8. Dispose of Used Oil and Filters:
– Take the used oil and filters to a recycling center to ensure environmentally responsible disposal.

Specific Call-Outs for the 2019 Sherco 300 SE Factory:

– Engine Type: The 2019 Sherco 300 SE Factory is a four-stroke motorcycle, which means it requires regular oil changes to maintain engine health.
– Oil Capacity: Ensure you use the correct amount of oil, as overfilling can be detrimental to the engine.
– Drain Plug Location: Be aware of the location of all drain plugs and ensure they are properly secured with new gaskets after each oil change.
– Titanium Parts: Be cautious around components like titanium exhausts to avoid damage.

By following these steps and paying attention to the specific nuances of your motorcycle, you can ensure your 2019 Sherco 300 SE Factory continues to perform at its best. Regular maintenance is key to extending the life of your bike and maintaining its performance.

Related Shopping Categories

Shop Motor Oil for a 2019 Sherco 300 SE Factory Dirt Bike.

Shop Oil Filters for a 2019 Sherco 300 SE Factory Dirt Bike.

Shop Oil Drain Pans for a 2019 Sherco 300 SE Factory Dirt Bike.

Shop Tools for a 2019 Sherco 300 SE Factory Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2019 Sherco 300 SE Factory Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.