How to Change the Oil in a 2019 Husqvarna FC250

Shop parts for a 2019 Husqvarna FC250 Dirt Bike.

Proprietary content for MotoSport.com

Tools and Supplies You’ll Need

  • 13mm socket or wrench (for drain bolt)
  • Pin wrench (for oil screen removal)
  • Torque wrench
  • Drain pan
  • Shop towels or rags
  • New oil filter
  • New crush washer (recommended)
  • Engine oil (check manual, typically 10W-50 full synthetic for this model)
  • Measuring cup (for oil quantity, 1.2L recommended but confirm in your manual)
  • Contact cleaner (to clean residual oil from parts)
  • Paper funnel (to avoid spills)
  • Gloves (to protect your hands)

Step-by-Step Oil Change Procedure

  1. Warm Up the Engine
    • Start your 2019 Husqvarna FC250 and let it idle for a few minutes. This helps the oil flow better and ensures contaminants are suspended in the oil for better drainage.
  2. Prep the Bike
    • Turn the engine off.
    • Place the bike upright on a stand on a level surface.
  3. Drain the Old Oil
    • Place the drain pan under the engine.
    • Use the 13mm socket/wrench to remove the oil drain bolt (located on the bottom of the engine).
    • Let the oil drain completely.
  4. Remove and Inspect the Oil Screen
    • Locate the oil screen screw plug (on the other side of the engine).
    • Use a pin wrench to carefully remove the screw plug and pull out the oil screen.
    • Inspect the screen for metal debris. Small metallic particles are normal, but chunks can indicate internal issues.
    • Thoroughly clean the screen and plug, then set aside.
  5. Replace the Oil Filter
    • Locate and remove the oil filter cover (typically secured by two bolts).
    • Pull out the old oil filter and dispose of it properly.
    • Install the new oil filter (prime it with clean oil beforehand if desired).
    • Reinstall the oil filter cover, tightening bolts to the manufacturer’s torque specification.
  6. Reinstall Drain Bolt and Oil Screen
    • If replacing, install a new crush washer on the drain bolt.
    • Reinstall the drain bolt and tighten to manufacturer’s specified torque.
    • Insert the cleaned oil screen back into place and reinstall the screw plug, torquing to spec.
  7. Add Fresh Oil
    • Remove the oil fill cap on the engine case.
    • Using a clean funnel, add fresh engine oil (1.2L recommended; confirm in your manual for exact amount).
    • Reinstall the oil fill cap.
  8. Check Oil Level
    • Start the engine and let it idle for three minutes, then turn it off.
    • Let the bike sit for a minute, then check the sight glass on the case. Oil should reach between halfway and three-quarters on the window. Top up if necessary.
    • If you overfill, drain a small amount using the drain bolt.
  9. Dispose of Old Oil Responsibly
    • Pour used oil and filter into a sealed container and take them to a recycling center.

2019 Husqvarna FC250 Specific Notes

  • This bike uses two oil screens, one on each side of the engine. Both must be removed and cleaned at each oil change (consult your owner’s manual for exact location).
  • Drain bolt and oil screen plug torque specs are crucial—always confirm in the service manual to avoid damaging threads.
  • Always use high-quality, manufacturer-recommended synthetic oil for optimal engine protection, especially in high-performance models like the FC250.
  • Avoid over-tightening any bolts—a common mistake that can cause leaks or cracked cases.
  • Change your oil more frequently if you ride in dusty or sandy conditions.

Quick Reference Table

Component Spec/Notes
Oil Quantity 1.2L (check your specific manual)
Oil Type Full synthetic 10W-50 (or manufacturer’s recommendation)
Drain Bolt Torque Consult owner’s manual (approx. 15 Nm typical)
Oil Filter Change every oil service (OEM part preferred)
Crush Washer Replace every time

Final Tips

  • Double-check for oil leaks after your first short ride.
  • Document your oil change intervals and hours in a log for engine longevity and warranty purposes.
  • Keep extra crush washers and a spare filter in your garage for easy, routine maintenance.

By following these steps and adhering to 2019 Husqvarna FC250-specific requirements, you’ll keep your dirt bike running strong and performing at its best.

Related Shopping Categories

Shop Motor Oil for a 2019 Husqvarna FC250 Dirt Bike.

Shop Oil Filters for a 2019 Husqvarna FC250 Dirt Bike.

Shop Oil Drain Pans for a 2019 Husqvarna FC250 Dirt Bike.

Shop Tools for a 2019 Husqvarna FC250 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2019 Husqvarna FC250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.