How to Change the Oil in a 2017 Yamaha TW200: Step-by-Step Guide

Shop parts for a 2017 Yamaha TW200 Dirt Bike.

Proprietary content for MotoSport.com

Tools and Materials Needed

  • 10mm and 12mm sockets or wrenches (for drain bolt and oil filter housing)
  • Torque wrench (recommended for proper bolt tightening)
  • Oil catch pan
  • Funnel
  • Rag or shop towels (for cleaning up spills)
  • Replacement oil filter (Yamaha part number or equivalent for TW200)
  • New engine oil (Yamaha recommends 10W-40, but always check your owner's manual for confirmation)
  • Replacement O-rings (recommended, especially for older or high-mileage bikes)
  • Peg stand or center stand (optional, helps keep the bike upright for level oil draining and checking)

Preparation and Safety

  • Warm up the engine for a few minutes. This helps the oil drain more completely and suspends contaminants in the oil.
  • Shut the bike off and let it sit for a minute, ensuring it's upright and on a level surface.

Oil Change Procedure for the 2017 Yamaha TW200

  1. Remove the Skid Plate (if installed):
    • Use the 10mm or 12mm socket to remove bolts and take off the skid plate to access the drain bolt.
  2. Remove the Oil Filler Cap:
    • This is located on the right side of the engine. Removing it helps the oil drain out faster and prevents vacuum lock.
    • Wipe dirt away from the area before opening to prevent contaminates from entering.
  3. Drain the Engine Oil:
    • Place your oil pan under the drain bolt (bottom of engine, left side).
    • Using the 12mm socket, loosen and remove the drain bolt. Let oil fully drain out–this may take 5–10 minutes.
    • While oil is draining, inspect and clean the magnetic tip of the drain bolt for metal debris.
    • Check the drain plug washer/O-ring and replace if damaged.
  4. Remove and Replace the Oil Filter:
    • Use the appropriate socket to remove the three bolts on the oil filter cover (right side of engine).
    • Remove the old oil filter and O-ring (carefully note orientation).
    • Clean the oil filter housing and inspect/replace O-ring if worn or damaged.
    • Install the new oil filter, ensuring correct orientation towards the engine.
    • Reinstall and torque the filter cover bolts to the manufacturer specification.
  5. Clean and Install the Drain Bolt:
    • After oil stops dripping, reinstall the drain bolt (with new washer if needed) and tighten to specified torque (check owner's manual, typically 17 ft-lbs but verify for your year). Overtightening can strip threads.
  6. Add Fresh Oil:
    • Insert the funnel into the filler hole and pour in new oil. The 2017 TW200 requires approximately 1.1 liters (1.16 US quarts) when changing oil and filter.
    • Replace the filler cap.
  7. Run and Check:
    • Start the engine and let it idle for one minute. Shut off and let it sit for another minute.
    • Check the oil level using the sight glass on the right side of the engine. Oil should be between the upper and lower marks. Upright the bike for an accurate reading.
    • If the level is low, add small amounts until the oil sits within the marks.
  8. Reinstall Skid Plate and Clean Up:
    • Once level is set, reinstall the skid plate.
    • Clean up any spilled oil and properly dispose of the used oil and filter at an approved recycling center.

Model-Specific Call-Outs and Tips for the 2017 Yamaha TW200

  • Oil Capacity: The TW200 takes about 1.1L with an oil and filter change.
  • Oil Filter Orientation: The filter has a correct orientation—open end faces out. Double-check if unsure during reinstallation.
  • Sight Glass: Check oil level with the bike upright; if checking alone, have someone help you balance it.
  • O-Rings: Replace O-rings on the filter cover and drain bolt if they appear cracked or deformed; this is especially important for older or higher-mileage bikes.
  • Torque Specs: Always use a torque wrench for drain bolt and filter cover bolts to avoid overtightening/stripping.
  • First Change: If this is the first oil change (break-in), be prepared for extra fine metallic debris on the magnetic drain plug—this is normal for new engines.

Final Thoughts

  • An oil change on the TW200 is straightforward and a critical part of maintenance that keeps your Yamaha running at its best.
  • Follow recommended service intervals in your owner's manual for ideal engine longevity.
  • For the best fit and peace of mind, use Yamaha OEM filters and quality oil matching the manufacturer's viscosity and grade recommendations.

Related Shopping Categories

Shop Motor Oil for a 2017 Yamaha TW200 Dirt Bike.

Shop Oil Filters for a 2017 Yamaha TW200 Dirt Bike.

Shop Oil Drain Pans for a 2017 Yamaha TW200 Dirt Bike.

Shop Tools for a 2017 Yamaha TW200 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2017 Yamaha TW200 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.