How to Change the Oil in a 2017 Husqvarna FE250HQ

Shop parts for a 2017 Husqvarna FE250HQ Dirt Bike.

Regular oil changes are crucial for maintaining peak engine performance and extending the lifespan of your 2017 Husqvarna FE250HQ dirt bike. This comprehensive guide, proprietary to MotoSport.com, will walk you through the process step-by-step, detailing all tools needed and any model-specific tips riders should know.

Tools and Supplies Needed

  • Socket wrench set (with correct socket size for oil drain plug and cover bolts)
  • Torque wrench
  • Drain pan
  • New oil filter (model-specific)
  • New engine oil (refer to your manual for recommended type and quantity; expect around 1,200 ml)
  • Replacement crush washer (for drain bolt)
  • Funnel
  • Clean rags or shop towels
  • Contact cleaner (optional for cleanup)
  • Grease (for oil filter cover seal)
  • Measuring cup
  • Owner's manual (for torque specs and capacities)

Steps to Change the Oil

  1. Warm Up the Engine
    • Start the bike and let it idle for 2-3 minutes. This helps the oil drain more completely by thinning it. Warning: The engine and oil will be hot; exercise caution to avoid burns.
      Reference: "Danger of scalding Engine and gear oil get very hot when the motorcycle is ridden."
  2. Park and Prepare
    • Turn off the bike and park it on a level surface.
    • Remove the skid plate, if fitted, to access the drain plug and oil screens.
  3. Drain the Old Oil
    • Place your drain pan directly under the engine's oil drain plug.
    • Carefully remove the drain plug using the socket wrench and let the old oil flow into the pan.
    • Allow a few minutes for complete draining.
    • Remove the oil filter cover and take out the oil filter. On this model, it is common to "prime" the new filter with a bit of oil before installing for better start-up lubrication.
    • Inspect and clean the oil screens with contact cleaner before replacing them. This ensures any debris is removed from the lubrication system.
  4. Install New Oil Filter and Replace Drain Plug
    • Lightly grease the oil filter cover seal to ease reassembly and prevent leaks.
    • Install the new oil filter and cover.
    • Replace the oil screens if they were removed, ensuring they are properly seated.
    • Install a new crush washer on the drain plug before threading it back in by hand to avoid cross-threading, then torque to specification using the torque wrench. Always check your owner's manual for the correct torque figure.
  5. Add New Engine Oil
    • Reinstall the skid plate if you removed it.
    • Remove the oil fill cap.
    • With a funnel, add approximately 1,200 ml (verify your manual for accurate capacity specific to your bike).
  6. Check Oil Level
    • Start the engine and let it run for 2-3 minutes. This distributes the oil through the engine.
    • Allow the bike to sit for a minute, then check the oil level in the sight glass on the engine. It should be at least halfway up to three-quarters of the window. Add oil as needed.
    • Do not exceed the maximum mark; overfilling can cause engine issues.
  7. Inspect for Leaks and Clean Up
    • Inspect all areas where work was performed for any signs of leakage.
    • Clean up any spilled oil, dispose of the old oil and filter properly as per local regulations.

2017 Husqvarna FE250HQ-Specific Call-Outs

  • Verify Oil Capacity: Always refer to your owner's manual for the correct oil capacity. The 1,200 ml figure is typical but confirmation is needed for your exact model.
  • Check the Oil Level Window: Ensure oil reaches at least the halfway mark but does not go above three-quarters for proper engine lubrication.
  • Oil Filter Orientation: Take care to install the oil filter in the correct direction, as improper installation may restrict oil flow.
  • Crush Washer Replacement: The drain bolt's crush washer should always be replaced to prevent leaks and maintain proper sealing.
  • Service Intervals: Oil changes are recommended at least every 15 engine hours. Aggressive or dusty riding may require more frequent changes.

Tips for a Clean and Easy Oil Change

  • Change your oil in a clean area to avoid getting debris inside the engine.
  • Dispose of used oil and filters responsibly at an appropriate recycling facility.
  • Keep a maintenance log to track oil changes and other upkeep tasks.

Conclusion

Changing the oil on your 2017 Husqvarna FE250HQ is straightforward with the right tools and some attention to detail. By following these steps, using quality materials, and observing correct oil specifications, you'll help ensure a long life and reliable performance from your dirt bike. For all maintenance parts and more, MotoSport.com is your one-stop shop.

Related Shopping Categories

Shop Motor Oil for a 2017 Husqvarna FE250HQ Dirt Bike.

Shop Oil Filters for a 2017 Husqvarna FE250HQ Dirt Bike.

Shop Oil Drain Pans for a 2017 Husqvarna FE250HQ Dirt Bike.

Shop Tools for a 2017 Husqvarna FE250HQ Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2017 Husqvarna FE250HQ Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.