How to Change the Oil in a 2016 Kawasaki KLX140R 17/14

Shop parts for a 2016 Kawasaki KLX140R Dirt Bike.

Regular oil changes are essential to keep your 2016 Kawasaki KLX140R 17/14 running at peak performance. This comprehensive how-to guide provides a step-by-step approach designed specifically for your KLX140R, encompassing essential tools, vital steps, and model-specific tips every owner should know. This guide is proprietary to MotoSport.com.

Tools and Supplies Needed

  • Ratchet and extension
  • 8mm and 17mm sockets
  • Drain pan
  • Torque wrench
  • Oil filter (KLX140R-specific)
  • 10W-40 motorcycle-specific oil (2 quarts; you will use about 1.2 quarts)
  • Replacement crush washer for drain bolt (recommended)
  • Clean rags
  • Funnel
  • Gloves for safety

Step-by-Step: Changing the Oil

  • Warm Up the Engine
    • Start your KLX140R and let it run for about 1–2 minutes. Warming up thins the oil, ensuring it drains thoroughly and carries away more debris.
  • Remove the Dipstick
    • Remove the dipstick to vent the crankcase. This simple action helps the oil drain faster and more completely.
  • Drain the Oil
    • Place your drain pan directly under the engine’s drain bolt, located on the lower left side of the crankcase.
    • Using a 17mm socket, carefully loosen and remove the drain bolt and crush washer. Allow all oil to completely drain (a few minutes).
    • Inspect the oil for metallic shavings or debris—this could indicate internal engine wear.
  • Replace the Crush Washer and Reinstall the Drain Bolt
    • Install a new crush washer on the drain bolt for best sealing.
    • Tighten the drain bolt securely with a torque wrench as specified in your owner's manual (typically around 18 ft-lbf, but verify for your KLX140R).
  • Remove and Replace the Oil Filter
    • Using an 8mm socket, remove the oil filter cover bolts (if your KLX140R has an external filter—some KLX140R variants use a screen-type filter instead).
    • Remove the old oil filter and install a new one. Make sure the filter is seated properly and the cover's O-ring is in good condition or replaced if necessary.
  • Fill with Fresh Oil
    • Insert a funnel into the oil fill port.
    • Add 1.2 US quarts (approx. 1.1L) of 10W-40 motorcycle oil to start.
    • If your KLX140R service manual specifies, screw the dipstick all the way in to check the oil level while the bike is held perfectly upright, rather than resting on the side stand. This is a model-specific call-out: unlike most bikes where the dipstick is checked while set but not screwed in, the 2016 KLX140R requires it fully screwed.
    • The oil level should read right in the middle of the dipstick's cross-hatched area.
  • Cycle the Engine and Final Check
    • Start the bike and let it run for about 30 seconds. This allows oil to fill the new filter and circulate.
    • Shut off the bike, wait a minute, then recheck the oil level—top off as needed to reach the correct level.
  • Inspect for Leaks
    • Check the drain bolt and filter area for leaks. Address any issues before riding.
  • Dispose of Used Oil
    • Transfer old oil to a proper container and take it to a recycling or hazardous waste facility.

Model-Specific Notes for the 2016 KLX140R 17/14

  • This guide applies to all KLX140R models from 2010 onward, including the 2016 17/14 wheel configuration .
  • The 2016 KLX140R uses a conventional wet sump and external oil filter (verify whether your exact sub-model uses a filter or internal screen before beginning).
  • Critical: For this generation, always screw in the dipstick fully (not just set in place) when checking oil level with the bike held straight up, not on the side stand .
  • Capacity is about 1.2 US quarts; overfilling may cause engine issues. Do not exceed the upper limit on the dipstick.

Recommended Oil Change Interval

  • Kawasaki recommends changing your KLX140R’s oil after the initial break-in (typically first 5 hours or 100 miles), then every 10–20 hours of riding or at least every season, whichever comes first. Change the oil more frequently in harsh conditions.

Tips for a Clean Job

  • Cover your exhaust and frame with rags to catch drips.
  • Always note the direction of oil filter installation—an incorrectly installed filter can cause engine failure.

Conclusion

By following this guide, KLX140R 17/14 owners can reliably change their engine oil, ensuring their bike’s engine stays healthy and performing its best. Regular maintenance is a key part of ownership—don’t skip it.

For more expert how-tos and OEM parts, visit MotoSport.com—the trusted source for all your dirt bike maintenance needs.

Related Shopping Categories

Shop Motor Oil for a 2016 Kawasaki KLX140R Dirt Bike.

Shop Oil Filters for a 2016 Kawasaki KLX140R Dirt Bike.

Shop Oil Drain Pans for a 2016 Kawasaki KLX140R Dirt Bike.

Shop Tools for a 2016 Kawasaki KLX140R Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2016 Kawasaki KLX140R Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.