How to Change the Oil in a 2016 Honda CRF110F: Step–by–Step Guide
Shop parts for a 2016 Honda CRF110F Dirt Bike.
Keeping the engine oil fresh in your 2016 Honda CRF110F is vital for ensuring a long, healthy engine life and optimal performance. This guide, proprietary to MotoSport.com, will walk you through the complete oil change process, including all required tools, stepwise instructions, and key model-specific tips to make your maintenance straightforward and successful.
Tools and Materials Needed
- 17 mm wrench or socket
- Oil drain pan
- Rag or paper towels (for cleanup)
- New engine oil (Honda-recommended, 1.0 liter)
- New sealing washer for drain bolt
- Torque wrench (capable of 24 N·m or 18 lbf·ft)
- Oil fill cap/dipstick (already on bike)
- Funnel (helps prevent spills)
- Gloves (optional, for protection)
Preparation Steps
- Be sure your bike is parked on a firm and level surface.
- Start the engine and let it idle for 3–5 minutes to warm up the oil. Warm oil drains more thoroughly, carrying away more contaminates.
- Shut off the engine and let the bike stand for 2–3 minutes so the oil settles in the sump.
Step-by-Step Oil Change Procedure
-
Remove the Oil Fill Cap/Dipstick
- Unscrew the oil fill cap/dipstick located on the right side of the engine. Set it aside where it won’t pick up dirt.
Tip: Removing this cap helps the oil drain more smoothly by preventing a vacuum. -
Position the Drain Pan
- Place your drain pan directly underneath the engine’s drain bolt (bottom right of the engine). -
Remove the Drain Bolt
- Using a 17 mm wrench or socket, loosen and remove the oil drain bolt and old sealing washer.
- Allow the oil to drain out completely. Slightly tilt the bike side to side to expel as much oil as possible.
Warning: Do not remove the cam chain tensioner push rod bolt (located adjacent to the drain bolt). Doing so may require dealer service to fix[]. -
Inspect and Replace Drain Components
- Once the oil finishes draining, clean the area around the drain bolt hole.
- Discard the old sealing washer; always use a new sealing washer to avoid leaks. -
Reinstall the Drain Bolt
- Refit the drain bolt with the new washer and tighten to 24 N·m (18 lbf·ft) with a torque wrench[]. -
Add New Engine Oil
- Double check that you’re using Honda-recommended oil at the correct viscosity (check your owner’s manual for details; a high-quality 10W-30 or 10W-40 is typical).
- Pour in 1.0 liter (approximately 1.1 US quarts).
- Using a funnel can help avoid spills.
Specific tip: The oil fill has a built-in spout for easier pouring on some bottles[]. -
Check and Secure the Oil Fill Cap
- Make sure the O-ring on the fill cap is clean and in good condition.
- Reinstall the oil fill cap/dipstick securely. -
Run the Engine and Check Oil Level
- Start the engine and let it idle for 2–3 minutes. This circulates the new oil.
- Turn off the bike and allow the oil to settle for a few minutes.
- Remove the dipstick, wipe it clean, reinsert (do not thread in), and check the oil level. The oil should be at or just below the upper mark on the dipstick.
- Add a little more oil if necessary (do not overfill)[].
-
Inspect for Leaks
- Look around the drain bolt and oil filter cap for signs of leaks. Tighten gently if needed (never overtighten). -
Proper Disposal
- Pour used oil into an appropriate container and take it to a recycling center or auto shop for safe disposal.
2016 CRF110F-Specific Call-Outs
- The oil capacity is 1.0 liter for a standard oil change, or 1.15 liter after a full disassembly, but regular oil changes just require 1.0 liter[]. Always double-check your dipstick to avoid over- or underfilling.
- There is no replaceable oil filter—just an internal oil screen. This screen only needs to be checked or cleaned periodically, not at every oil change. When servicing the screen, a new right-hand case cover gasket may be required[].
- Always use a new sealing washer on the drain bolt to prevent leaks[].
- To drain as much old oil as possible, it helps to lean the bike gently side to side while the drain bolt is out[].
- Avoid removing any additional bolts; the cam chain tensioner push rod bolt is directly adjacent to the drain bolt and should not be removed during an oil change[].
Final Check and Clean Up
- Take a short ride or run the engine outside for a couple of minutes, then double-check for any leaks and confirm oil level.
- Clean up your work area and store leftover oil in a safe, labeled container for future use or disposal.
Conclusion
Changing the oil on your 2016 Honda CRF110F is a straightforward maintenance task that you can confidently tackle with basic tools and supplies. Keep to this process every 15–20 hours of use or as specified in your maintenance schedule to maximize your CRF110F’s reliability and riding fun.
Proprietary content by MotoSport.com
Related Shopping Categories
Shop Motor Oil for a 2016 Honda CRF110F Dirt Bike.
Shop Oil Filters for a 2016 Honda CRF110F Dirt Bike.
Shop Oil Drain Pans for a 2016 Honda CRF110F Dirt Bike.
Shop Tools for a 2016 Honda CRF110F Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2016 Honda CRF110F Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.