How to Change the Oil in a 2014 Husqvarna FE250HQ: Complete Guide

Shop parts for a 2014 Husqvarna FE250HQ Dirt Bike.

This proprietary MotoSport.com guide walks you step-by-step through how to change the oil in your 2014 Husqvarna FE250HQ dirt bike. Regular oil changes are critical to engine longevity and performance. Below you'll find recommended tools, exact steps, and important call-outs every FE250HQ owner should know.

Tools & Supplies Needed

  • Socket wrench set (preferably with 8mm and 13mm sockets)
  • Torque wrench (for drain bolts and cover bolts)
  • Drain pan
  • Replacement oil (Motorex 10W-50, or oil recommended in your manual)
  • New oil filter (OEM or high-quality aftermarket, model-specific)
  • New oil filter O-ring (strongly recommended)
  • Crush washer (for drain plug, if required)
  • Funnel
  • Shop towels or rags
  • Gloves (optional, but helps keep things clean)

Preparation & Safety

  • Warm up the engine for a few minutes. This allows the oil to drain out more completely later.
  • Clean the area around the oil fill cap, drain bolt, and oil filter cover to prevent debris from entering the engine.
  • Park the bike upright on a stable surface or a stand.

Step-by-Step Oil Change Instructions

  1. Remove the Skid Plate (if equipped):
    • Most FE250HQ models have a skid plate that partially covers the drain plug. Unbolt this first for access to the sump area.
  2. Locate the Drain Bolts:
    • Main oil drain bolt is on the bottom of the engine case; check your owner's manual for the exact position if unsure.
    • Some Husqvarna and KTM designs have a second drain bolt or mesh filter–remove both to fully drain the oil.
  3. Drain the Old Oil:
    • Position your drain pan under the drain bolt(s).
    • Remove the fill cap first (on top of the right engine cover) to allow oil to flow out easily.
    • Unscrew the drain plug(s) and let the oil flow out completely—this may take 5-10 minutes.
    • Inspect the crush washer/gasket on the drain bolt and replace if damaged or flattened.
  4. Remove & Inspect Oil Filter:
    • Unbolt the oil filter cover (typically three 8mm bolts on the right side).
    • Remove the old filter and inspect it for any excessive metal shavings or debris; this can indicate engine wear.
    • Wipe the inside of the cover and seating area clean.
    • Critical call-out: The 2014 FE250 uses a cartridge-style oil filter—make sure your replacement matches.
  5. Install the New Filter & O-ring:
    • Lightly oil the new O-ring and the rubber gasket on the oil filter (if equipped).
    • Insert the new filter into the engine (follow directional arrows if marked), making sure it seats correctly.
    • Reinstall the filter cover bolts. Torque them evenly to the spec in your service manual to avoid leaks.
  6. Reinstall Drain Plug(s):
    • Once oil is fully drained, clean and reinstall drain plug(s) with new crush washers if needed. Always torque to manufacturer's specification (typically around 15 Nm, but check your manual).
  7. Add Fresh Oil:
    • Use a funnel to pour in about 900-1000 ml (consult the manual for exact capacity), starting with a little less than full capacity.
    • Replace the fill cap.
    • Start the engine and let it idle for 1-2 minutes, then shut off and let settle for 2 minutes.
    • Check the oil level in the sight glass (on the right engine cover). Top up if needed.
  8. Check for Leaks:
    • Inspect around the drain plug and oil filter cover. Wipe away excess oil and monitor for drips while the engine is running.
  9. Reinstall Skid Plate:
    • If you removed it, bolt the skid plate back on before riding.
  10. Dispose of Old Oil Responsibly:
    • Pour old oil into a sealable container and take it (with old filters) to a local motorcycle shop, auto parts store or recycling center.

FE250HQ Model-Specific Call-Outs

  • Always use premium oil: These engines are high-revving and designed for performance—the manufacturer recommends Motorex 10W-50 or equivalent.
  • Oil screens: The FE250/350 engines may have mesh oil screens near the drain plug–remove and clean them during each oil change.
  • Torque specs are critical: The smaller bolts on Husqvarna dirt bikes are easy to overtighten. Consult your owner's manual and use a torque wrench.
  • Check for updates: Some early FE models had updates to oil screen placement or drain bolt design—reference your manual or authorized dealer for the most up-to-date information on your 2014 model.

Summary

Changing the oil in your 2014 Husqvarna FE250HQ takes about 30 minutes with the right tools. Pay attention to cleanliness, double-check torque specs, and always use recommended fluids. Following these steps will keep your engine running at peak MotoSport.com performance every ride.

Related Shopping Categories

Shop Motor Oil for a 2014 Husqvarna FE250HQ Dirt Bike.

Shop Oil Filters for a 2014 Husqvarna FE250HQ Dirt Bike.

Shop Oil Drain Pans for a 2014 Husqvarna FE250HQ Dirt Bike.

Shop Tools for a 2014 Husqvarna FE250HQ Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2014 Husqvarna FE250HQ Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.