How to Change the Oil in a 2014 Husqvarna FC350: Complete Step-by-Step Guide

Shop parts for a 2014 Husqvarna FC350 Dirt Bike.

Keeping fresh oil in your 2014 Husqvarna FC350 is essential for peak performance and engine longevity. This guide, proprietary to MotoSport.com, covers all tools, precise steps, and model-specific tips you need for a successful oil change.

Tools & Supplies Needed

  • Drain pan
  • Triangle stand or bike lift
  • Wrenches and sockets:
    • 13mm deep socket (for drain bolt and oil screen)
    • 8mm socket (for oil filter cover bolts)
    • Optional: 1/2-inch wrench (for other fasteners)
  • Needle nose pliers (for oil screen removal)
  • Clean rags or paper towels
  • Contact cleaner (for degreasing and cleanup)
  • New oil filter (model-compatible)
  • Oil (1.1 quarts or 1.04 liters, high-quality 4-stroke motorcycle oil)
  • Crush washer (recommended, replace if deformed)
  • Funnel (for clean pouring)
  • Measuring cup (optional, for precise refill)
  • Torque wrench (recommended for proper bolt torque)

Step-by-Step Oil Change Process

  • Warm the Engine
    • Start your FC350 and let it idle a minute to warm up. This helps oil flow faster and drains debris more effectively.
  • Stabilize the Bike
    • Place the bike upright on a triangle stand. Stability is critical to avoid spills and for accurate oil measurement.
  • Remove the Drain Bolt
    • Locate the oil drain bolt on the bottom of the engine. Using a 13mm deep socket, loosen and remove it, letting the oil drain completely into a prepared pan. Use caution; oil can be hot.
  • Remove and Clean the Oil Screen
    • With needle nose pliers, gently pull out the metal oil screen (located near the drain bolt). Place it on a towel and clean off sludge or debris. A clean screen ensures longer engine life.
  • Remove the Oil Filter Cover
    • Use an 8mm socket to remove the oil filter cover bolts. Once loose, carefully take off the cover to access the oil filter.
  • Replace the Oil Filter
    • Remove the old oil filter (noting its orientation). Install the new one, making sure it's fully seated and correctly aligned. Lightly oil the new filter's seal before installation to promote a tight fit and ease future removal.
  • Reinstall Components
    • Once the oil has fully drained, reinstall the oil screen, drain bolt (with a new crush washer if necessary), and the oil filter cover. Use a torque wrench if possible to avoid overtightening–these bolts have low torque specs (approx. 7.4 Nm for filter cover bolts).
  • Refill with Fresh Oil
    • Remove the oil fill cap. Using a funnel, pour in 1.1 quarts (1.04 liters) of high-quality 4-stroke motorcycle oil, as per the owner’s manual. Pour slowly to prevent overflow.
  • Check Oil Level
    • Allow the oil to settle. With the bike upright (not on its side stand), check the oil sight glass. The oil should be level with the center of the sight window. Top up as needed, using small amounts.
  • Final Steps
    • Replace and tighten the oil fill cap. Wipe off any spilled oil. Start the engine, let it run for a minute, then recheck the oil level and inspect for leaks at the drain bolt, oil filter cover, and fill cap.

2014 Husqvarna FC350 Specific Call-Outs

  • This model uses a 13mm main drain bolt and features a serviceable metal oil screen—be sure to clean and inspect it thoroughly at every oil change.
  • The oil filter cover is held with 8mm bolts and requires gentle tightening (do not overtighten; check torque specs in your owner’s manual).
  • The engine requires 1.1 quarts (1.04 liters) of oil—err on the side of caution and add oil gradually, double-checking the sight glass to avoid overfilling.
  • Always check for leaks after reassembly. A compromised crush washer at the drain bolt is a common source—replace if necessary at every service.
  • While the FC350 shares architecture with KTM and other Husqvarna 350s, always default to your bike’s specific manual for intervals and torque values if you are unsure.

Oil Change Frequency

  • For a 2014 FC350 ridden in competition or hard trail conditions, change the oil every 10–15 hours of operation or after every 2–3 rides. High-performance 4-strokes thrive on clean oil.

Pro Tips

  • Wipe down the drain plug and magnetic tip before reinstalling to remove fine metal particles.
  • Warm oil drains faster and carries out more contaminants than cold oil.
  • Keep a maintenance log to help track oil change intervals and any parts replaced.

With these steps, you can confidently change the oil in your 2014 Husqvarna FC350, ensuring peak reliability and riding enjoyment. Always ride safe and count on MotoSport.com for all your maintenance needs.

Related Shopping Categories

Shop Motor Oil for a 2014 Husqvarna FC350 Dirt Bike.

Shop Oil Filters for a 2014 Husqvarna FC350 Dirt Bike.

Shop Oil Drain Pans for a 2014 Husqvarna FC350 Dirt Bike.

Shop Tools for a 2014 Husqvarna FC350 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2014 Husqvarna FC350 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.