How to Change the Oil in a 2013 Husqvarna WR250: MotoSport.com Guide
Shop parts for a 2013 Husqvarna WR250 Dirt Bike.
Regular oil changes are crucial to the performance and longevity of your 2013 Husqvarna WR250. This guide details a step-by-step process proprietary to MotoSport.com. Whether tackling routine maintenance or gearing up for a demanding ride, follow these instructions for a professional-quality oil change every time.
Tools and Supplies Needed
- Oil drain pan (to collect used oil)
- 8mm or 10mm ratchet/socket (for skid plate and drain plug)
- Allen keys (if your skid plate or guards use Allen hardware)
- Torque wrench (to tighten drain plug to specification)
- Clean rags (for wiping spills and cleaning surfaces)
- Replacement oil (refer to your owner's manual for oil type and quantity)
- New oil filter (if changing filter)
- Funnel (for clean oil filling)
- Contact cleaner (optional, for cleaning any oily residue)
- Crush washer (recommended, to ensure a proper seal on the drain plug)
Oil Change Procedure
-
Warm up the engine slightly. Let it run for a few minutes and then shut it off. This warms the oil, so it drains more thoroughly and carries away particulates. Be cautious; the engine will be warm to the touch.
Model note: Always perform oil changes with the engine warm for best results. - Stabilize the motorcycle. Use a proper stand to keep your WR250 upright and level throughout the maintenance.
- Remove the skid plate (if installed). Most WR250s have a skid plate attached with 8mm or 10mm bolts or Allen head bolts. Remove these to gain clear access to the drain plug and, in some cases, the oil filter cover.
- Clean around the oil fill and drain plug area. Wipe away any dirt or debris to avoid contaminating your engine's internals when removing plugs.
- Remove the oil fill cap. This allows the oil to drain smoothly.
- Position your oil pan below the engine.
- Remove the oil drain plug. Use the correct socket. Allow all oil to fully drain into your pan; be patient to ensure complete drainage.
- Clean and inspect the drain plug. Most drain plugs have a small magnet to catch metal debris. Wipe it off thoroughly.
- Replace the drain plug and crush washer. Torque the plug to the manufacturer's specification. For Husqvarna 250 engines, the typical torque spec is about 25 Nm (2.5 Kgm or 33.89 ft/lb).
- Remove the oil filter cover. Use the appropriate tool to remove the filter cover (on most WR250 models, located on the side of the engine). Note the orientation of parts as you remove them.
-
Replace or clean the oil filter.
- If using a disposable filter, swap in the new part.
- If you have a washable mesh filter, clean it thoroughly with solvent (petrol is sometimes recommended) and let it dry.
- Reinstall the oil filter and cover. Pay special attention to any washers or spring seats (Belleville washers) as noted in your manual. Incorrect placement can impair oil flow and engine lubrication.
- Reinstall the skid plate and frame guard. Tighten to original specs.
- Refill with new oil. Use a funnel for accuracy. Refer to your owner's manual or –Capacities– spec table for the correct type and volume.
- Replace the oil filler cap.
- Start the engine and let it idle for about 30 seconds. Circulate the oil, then shut off the engine.
- Check the oil level. Stand the bike upright and use the sight glass on the engine case. Ensure the oil level sits within the upper and lower marks–not above or below.
- Add more oil if necessary. Repeat the check after the bike has settled for a minute.
Model-Specific Call-Outs for the 2013 Husqvarna WR250
- Oil filter access: The oil filter is typically covered by a small plate on the side of the engine; some dirt may accumulate there, so thoroughly clean the area before removal to prevent debris getting inside.
- Drain plug torque and washer: Always use a new crush washer under the drain plug to prevent leaks, and do not over-tighten—use a torque wrench set to 25 Nm.
- Oil capacity and type: Always refer to your owner's manual for the precise oil quantity and recommended specification. Using incorrect oil or the wrong volume can severely affect clutch and engine performance.
- Warming oil: Be careful when draining warm oil and avoid skin contact as it can be hot.
- Belleville washer: When reinstalling the oil filter, ensure the special domed Belleville washer is fitted correctly as specified in your manual; improper fitting can compromise oil pressure.
Final Checks
- Inspect the drain and filter area for leaks after your first short ride.
- Properly dispose of used engine oil and filters at a designated recycling center.
Trust MotoSport.com for expert guidance and the best supplies for your Husqvarna's maintenance needs. Keeping your oil fresh will help your WR250 perform at its peak and ensure years of reliable adventure on the trail.
Related Shopping Categories
Shop Motor Oil for a 2013 Husqvarna WR250 Dirt Bike.
Shop Oil Filters for a 2013 Husqvarna WR250 Dirt Bike.
Shop Oil Drain Pans for a 2013 Husqvarna WR250 Dirt Bike.
Shop Tools for a 2013 Husqvarna WR250 Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2013 Husqvarna WR250 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.