How to Change the Oil in a 2013 Husqvarna TXC250

Shop parts for a 2013 Husqvarna TXC250 Dirt Bike.

Keeping your 2013 Husqvarna TXC250 running strong requires regular oil changes to protect the engine and maximize performance. This robust guide, proprietary to MotoSport.com, covers all the steps, tools, and TXC250-specific call-outs you need to perform a safe and effective oil change at home.

Tools and Supplies Needed

  • 8mm, 12mm, and 13mm sockets and corresponding ratchet
  • Drain pan or bucket (to catch old oil)
  • Oil funnel
  • Fresh engine oil (consult your TXC250 manual for viscosity; 10W-50 fully synthetic is common, 950cc needed)
  • OEM oil filter (Husqvarna or equivalent)
  • Crush washer and O-rings (for drain bolt and oil filter cover)
  • Parts cleaner or brake cleaner
  • Needle nose pliers or a pick (to remove oil screen)
  • Torque wrench (critical for proper reinstallation)
  • Shop towels or rags
  • Gloves and safety glasses

Step-By-Step Oil Change Instructions

  • Warm Up the Engine
    • Idle the engine for 2–3 minutes to warm the oil. Do not overheat.
    • Turn off the bike and let it cool for a minute before working.
  • Remove the Skid Plate
    • If your TXC250 has a skid plate, remove it to access the drain plug more easily. Use the appropriate size socket or Allen wrench.
  • Drain the Old Oil
    • Place your drain pan beneath the engine’s drain bolt.
    • Use a 12mm socket to remove the drain plug. Be ready for oil to flow quickly.
    • Allow oil to drain completely.
    • Model-specific tip: The drain bolt on the 2013 TXC250 is a tight fit, especially with the frame cross-member close to the bolt. Use caution to avoid dropping the bolt or burning yourself as the oil drains. Patience is key for your first oil change.
  • Remove and Clean the Oil Screen
    • With the drain plug removed, use a pick or needle nose pliers to carefully extract the oil screen behind the drain bolt. It fits snugly but is sturdy.
    • Avoid damaging the screen. Clean it with brake cleaner and inspect for debris or metal shavings. If damaged, replace.
    • Reinstall the screen all the way in before replacing the drain screw. Insure it is secure in its groove, as an offset screen can allow contaminants past your oil pump.
  • Replace the Crush Washer
    • Replace the drain bolt’s crush washer with a new one to prevent leaks.
    • Thread the drain bolt in by hand, then torque to 14.8 ft-lbs (20 Nm) using a torque wrench.
  • Change the Oil Filter
    • Locate and remove the oil filter cover with an 8mm or 13mm socket, depending on fastener type.
    • Remove the old filter; note its direction for proper reinstallation.
    • Inspect and replace the filter cover O-rings if worn or flattened.
    • Install the new filter (lubricate O-rings with fresh oil).
    • Tighten the cover bolts evenly; do not overtighten.
  • Refill with Fresh Oil
    • Ensure the drain bolt and oil filter are properly installed.
    • Using a funnel, add 950cc (0.95 liters) of fresh engine oil through the oil fill cap on the right engine side. Use the recommended grade (often 10W-50 synthetic).
    • Wipe any spilled oil and reinstall the fill cap.
  • Check Oil Level and Leaks
    • Start the engine and let it idle for 30 seconds, then shut off and wait one minute.
    • Check for any leaks at the drain bolt and oil filter area. Tighten if necessary.
    • With the bike upright, check the level in the sight glass or with the dipstick. Add oil if needed.

TXC250-Specific Call-outs

  • The drain bolt is close to the frame, so oil removal can be messy and the bolt is easy to drop. Take your time and use a magnetic tool if needed.
  • There is one oil screen (on the 2013 TXC250), located behind the drain bolt. Remove and install it carefully with a pick all the way through for easy removal.
  • Filter orientation matters; always match the old filter’s direction.
  • If you see an unusual amount of metal shavings in the screen or filter, monitor closely and consider a deeper inspection.
  • The oil capacity for the TXC250 is 950cc (0.95 liters). Overfilling can cause leaks or running issues.

Disposal of Old Oil

  • Collect all used oil in a dedicated container and take it to a recycling center or your local motorcycle dealership for safe disposal. Never pour oil into the ground or down a drain.

Summary Table: 2013 Husqvarna TXC250 Oil Change Specs

Part Spec/Note
Engine oil amount 950cc (0.95 liters)
Recommended Oil 10W-50 fully synthetic
Drain Bolt Torque 14.8 ft-lbs (20 Nm)
Oil Filter Replace with every oil change; check O-rings
Oil Screen Remove, clean, and inspect for debris

MotoSport.com recommends performing oil changes according to your riding frequency, but a good rule is every 5–10 hours of aggressive riding or every month for moderate use. Stay ahead of your maintenance, and your Husqvarna TXC250 will reward you with long-lasting, dependable performance.

Related Shopping Categories

Shop Motor Oil for a 2013 Husqvarna TXC250 Dirt Bike.

Shop Oil Filters for a 2013 Husqvarna TXC250 Dirt Bike.

Shop Oil Drain Pans for a 2013 Husqvarna TXC250 Dirt Bike.

Shop Tools for a 2013 Husqvarna TXC250 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2013 Husqvarna TXC250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.