How to Change the Oil in a 2013 Husqvarna TE310: Full Guide for MotoSport.com

  • Changing the oil in your 2013 Husqvarna TE310 is key for engine longevity and performance. This robust how-to covers required tools, step-by-step instructions, and unique quirks about the TE310's oil change process.

Tools and Supplies Needed

  • Socket wrench set (metric sizes, mainly 8mm, 10mm, 13mm for covers and skid plate)
  • Screwdrivers (Phillips and flathead, for hose clamps or panel fasteners)
  • Drain pan
  • New oil filter (OEM recommended)
  • Fresh motorcycle oil (check manual for correct viscosity)
  • Funnel
  • Shop towels/rags
  • Contact cleaner (optional, for cleaning up any spillage)
  • Measuring cup (to ensure correct oil capacity)
  • Replacement crush washer for drain (recommended each oil change)
  • Gloves (optional for cleanliness and safety)

Before You Start: Unique Notes on the 2013 Husqvarna TE310

  • The TE310 uses a drain hose and clamp system rather than a traditional bolt at the crankcase. The hose drains oil when unplugged from the clamp, which is somewhat different from many dirt bikes that use a single drain bolt. Get familiar with this part before starting, as it's essential for a clean job and prevents confusion if you expect a regular drain plug .
  • Make sure the skid plate is removed. The TE310's oil drain hose is often covered or blocked by the skid plate. Remove it first by taking off the bolts and any holding clamps .
  • Always check for loose debris or dirt around the drain area before opening the system to avoid introducing contaminants to the engine .
  • If the drain hose seems damaged, replace it rather than risk a leak. Some users also swap the hose for a magnetic drain plug if compatible, but always use manufacturer-approved parts .

Step-by-Step: How to Change the Oil in a 2013 Husqvarna TE310

  1. Warm up the engine: Run the bike for a few minutes. This helps the oil flow out more easily and carries away debris suspended in the oil.
  2. Remove the skid plate: Using your socket set, undo the bolts/clamps securing the skid plate. Most TE310s will have both rear and front bolts or clamps. Pull off the plate and clean off any packed mud and debris. This provides access to the drain hose and keeps dirt from contaminating your oil change .
  3. Clean the drain area: Before touching the hose or clamps, use a rag or compressed air to fully clean the surrounding area.
  4. Locate the oil drain hose and clamp: The TE310's hose usually sits along the bottom of the engine. It's secured by a clamp, rather than a standard drain bolt .
  5. Position your drain pan: Slide a wide drain pan under the hose area. Have rags handy.
  6. Release the oil: Use pliers or a screwdriver to open the clamp and carefully remove the hose end from its spigot or plug. Oil will begin draining quickly. Let it drain completely: allow several minutes for old oil to fully empty. Tilt the bike gently side-to-side to help speed the process.
  7. Remove the oil filler cap: This allows the oil to drain more freely by preventing vacuum lock.
  8. Change the oil filter:
    • Locate the oil filter cover on the engine case (check your manual if unsure).
    • Remove the bolts or screws to take off the cover.
    • Carefully remove the old oil filter. Some oil will drip–use a rag.
    • Lubricate the new filter's rubber seal with fresh oil, then fit the new filter in place.
    • Reinstall the cover and torque bolts to spec (consult your workshop manual for exact torque values) .
  9. Inspect and replace crush washer: If your drain hose setup uses a crush washer, fit a new one to guarantee a proper seal.
  10. Secure drain hose: Once the oil has finished draining, replace the hose onto its fitting and secure the clamp tightly. Wipe the area clean.
  11. Refill fresh oil:
    • Using a funnel, pour in the recommended quantity and type of oil (always double-check your owner's manual for amount and viscosity).
    • Replace the filler cap securely.
  12. Check oil level:
    • Start the bike, let it idle for 30–60 seconds, then shut down and let oil settle for a minute or two.
    • Use the sight glass or dipstick to check the oil level. Top up if required.
  13. Reinstall skid plate: Bolt the skid plate back into place using your socket set.
  14. Dispose of old oil properly: Never pour it down drains or outside. Use a recycling center or parts store oil collection system.

2013 TE310-Specific Call-outs and Tips

  • The hose and clamp drain method on the TE310 is unusual compared to other Husqvarna models. Make certain the clamp is secure post-change, or you'll risk leaks .
  • Mud and debris can collect heavily around the skid plate and drain hose. Clean thoroughly to avoid introducing grit to the engine during oil removal.
  • Always use the correct oil filter for the TE310–filters from other Husqvarna or KTM models may look similar but could lead to fitment and filtration issues.
  • The oil fill capacity and service intervals may vary from other years/models. Always verify the oil volume in your user or workshop manual .
  • Magnetic drain plug upgrades are possible but check for compatibility. Stock setup is a hose and clamp, which must be kept in top condition to prevent leaks .

Final Thoughts

  • Regular oil changes keep your 2013 Husqvarna TE310 running at peak performance, reduces engine wear, and prevents costly maintenance later. Always follow the unique requirements of this model—especially its distinctive drain hose system—for the best results and safety.
  • For more information and OEM-grade parts, shop at MotoSport.com for filters, oil, and tools custom-selected for your TE310.

Related Shopping Categories

Shop Motor Oil for a 2013 Husqvarna TE310 Dirt Bike.

Shop Oil Filters for a 2013 Husqvarna TE310 Dirt Bike.

Shop Oil Drain Pans for a 2013 Husqvarna TE310 Dirt Bike.

Shop Tools for a 2013 Husqvarna TE310 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2013 Husqvarna TE310 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.