How to Change the Oil in a 2013 Husqvarna TC250: Step-–By-–Step Guide

Shop parts for a 2013 Husqvarna TC250 Dirt Bike.

Routine oil changes are critical for maintaining the performance and longevity of your 2013 Husqvarna TC250. This proprietary MotoSport.com guide walks you through the process, listing all necessary tools, providing detailed steps, and highlighting specific call-outs unique to the TC250 model.

Tools and Supplies Needed

  • Owner's manual (for specifications and torque values)
  • Socket wrench set
  • Oil drain pan
  • Torque wrench (to ensure proper tightening torque)
  • Contact cleaner or shop towels (for cleanup)
  • Measuring cup (to ensure proper oil level)
  • OEM recommended oil filter
  • Crush washer (replace if damaged)
  • Engine oil (type and quantity as specified in the manual; check "Capacities" table for the correct amount)
  • Rubber gloves (optional, for cleaner hands)

Model-Specific Call-Outs for 2013 Husqvarna TC250

  • You need a warm engine for best oil drainage–run your bike a few minutes before starting.
  • Do not remove the sump guard as it's designed to stay in place during the oil change.
  • The oil drain plug has a magnet–clean it thoroughly before reinstalling.
  • This model uses a mesh filter and a paper oil filter; both need attention during the change.
  • Check and install the Belleville washer correctly when replacing the filter cover.
  • Torque the drain plug to 25 Nm (2.5 Kgm or 33.89 ft/lb).
  • Always use the recommended oil type and quantity–refer to your owner's manual's capacities table.

Step-by-Step Oil Change Instructions

  • 1. Prepare Your Work Area and Bike
    • Make sure the area is well-ventilated and away from heat sources or open flames.
    • Stabilize the bike on a stand, ensuring it’s upright and secure.
    • Run the bike for a few minutes to warm the engine; this improves oil drainage.
  • 2. Remove Filler Cap
    • Locate and unscrew the oil filler cap. Set it aside on a clean surface to prevent contamination.
  • 3. Drain the Oil
    • Position an oil drain pan beneath the drain plug.
    • Remove the oil drain plug (found at the bottom of the engine). Be cautious–oil will be hot.
    • Let oil drain completely. Tilt the bike slightly toward you (about 30 degrees) to ensure complete drainage, as oil can pool in the engine recesses.
    • Locate the mesh filter and remove it gently for cleaning.
    • Thoroughly clean the drain plug and its magnet with a shop towel or soft brush.
  • 4. Clean or Replace the Filters
    • Wash the mesh filter in petrol (gasoline) and ensure it is free of debris and sludge before reinstalling.
    • Unscrew the oil filter cover; take out the old oil filter.
    • Install a new oil filter, making sure the Belleville washer is placed in the correct position.
    • Reinstall the cover and screws, tightening them evenly.
  • 5. Reinstall the Drain Plug – Components
    • Fit a new crush washer to the drain plug if necessary.
    • Reinstall the drain plug and torque it to 25 Nm (33.89 ft/lb).
    • Wipe away any spilled oil and inspect for leaks.
  • 6. Fill with New Oil
    • Using a funnel, fill the engine with the correct quantity and type of oil, as specified in your owner's manual.
    • Reinstall the filler cap.
  • 7. Final Checks
    • Start the engine and let it idle for a minute, then turn it off.
    • Check oil level using the dipstick or sight glass and top off if necessary.
    • Check for leaks at the drain plug and filter cover.
  • 8. Dispose of Old Oil Properly
    • Transfer used oil to a sealable container. Never pour oil down a drain; take it to an appropriate recycling center or auto parts store.

Expert Tips for Your TC250

  • Change the oil every 10–15 hours of ride time, depending on how hard you ride or conditions.
  • Inspect the mesh filter and drain plug magnet closely for any unusual metal shavings, which could indicate engine wear.
  • Always consult your owner’s manual for model-specific recommendations, especially for oil capacity and filter orientation.

Performing regular oil changes on your 2013 Husqvarna TC250 not only keeps your engine healthy but ensures peak track or trail performance every time you ride.

Related Shopping Categories

Shop Motor Oil for a 2013 Husqvarna TC250 Dirt Bike.

Shop Oil Filters for a 2013 Husqvarna TC250 Dirt Bike.

Shop Oil Drain Pans for a 2013 Husqvarna TC250 Dirt Bike.

Shop Tools for a 2013 Husqvarna TC250 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2013 Husqvarna TC250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.