How to Change the Oil in a 2011 Husqvarna TE310: A Complete Step-by-Step Guide

Shop parts for a 2011 Husqvarna TE310 Dirt Bike.

Keeping your 2011 Husqvarna TE310 running strong requires regular oil changes. This guide, exclusive to MotoSport.com, walks you through all the tools, steps, and unique considerations needed for a successful oil change on this specific dirt bike model.

Tools and Supplies Needed

  • Socket set (notably 8mm, 10mm, and 13mm sockets)
  • Allen wrench or hex key set
  • Screwdrivers (flathead and Phillips)
  • Oil drain pan
  • Shop rags or towels
  • Funnel
  • Replacement oil (see Owner’s Manual; typically fully synthetic 10W-60 for Husqvarna TE310)
  • New oil filter
  • Replacement sealing washer for the drain plug (optional but recommended)
  • Pliers (for hose clamps, if equipped)
  • Torque wrench
  • Latex or Nitrile gloves (for protection)

Pre-Oil Change Tips Specific to the 2011 Husqvarna TE310

  • Drain the oil with the engine warm; this ensures better flow and more complete removal of old oil and contaminants.
  • The oil drain point may be a hose and clamp assembly (rather than a typical bolt), so check your model for this design.
  • If applicable, the oil sump guard (skid plate) can remain in place for the TE310, unless it obstructs access.
  • Do not touch hot oil; wear gloves and be careful not to spill oil onto hot engine parts.
  • Make sure you have the recommended amount and type of oil–see your owner's manual for the capacity and manufacturer’s approved specification.

Step-by-Step Instructions

  1. Warm up the engine for a few minutes. Shut it off and allow it to cool just enough for safe handling–oil should be warm, not scalding.
  2. Locate the oil filler cap (on top of the engine case) and loosen/remove it for easier draining and quicker oil flow.
  3. Position an oil drain pan under the engine.
  4. Access the drain point:
    • If your TE310 has a skid plate obstructing access, remove it using the appropriate tools, usually socket or hex keys.
    • The 2011 Husqvarna TE310 sometimes uses a hose-and-clamp oil drain system. Use pliers to loosen the clamp, then carefully pull back the hose to let oil drain (have rags handy).
    • If your bike has a traditional drain bolt, use a socket/ratchet to remove it. Let the oil drain completely.
  5. Remove the old oil filter:
    • Locate the oil filter cover—generally on the right engine case.
    • Remove the cover screws with the appropriate size Allen or socket.
    • Note the order of assembly: filter cover, o-ring (or gasket), and filter.
    • Important: Be sure to fit the filter’s oil seal first onto the cover before reassembly, to prevent leaks.
  6. Install the new oil filter:
    • Wipe out the oil filter cavity with a clean rag.
    • Install the new filter in the same orientation as the old one.
    • Check or replace the oil filter cover O-ring/gasket if worn.
    • Reinstall the cover. Tighten bolts to manufacturer’s torque spec.
  7. Reinstall the oil drain hose or drain bolt.
    • Clean and inspect the sealing area and the washer. Replace the washer if damaged.
    • Re-tighten the hose clamp securely, or torque the drain plug to 25 Nm (2.5 Kgm or 33.89 ft-lb) as specified for this model.
    • If removed, reinstall the skid plate.
  8. Pour fresh oil into the engine:
    • Use a funnel to avoid spills. Fill with the manufacturer-specified quantity and type of oil. Consult your owner's manual for the exact volume required.
  9. Reinstall the oil filler cap and clean up any spills.
  10. Start the engine and let it idle for 30-60 seconds. Shut off and wait a couple minutes. Check the oil level and top off to correct height if needed.

TE310-Specific Tips and Cautions

  • Double-check for leaks around the oil drain hose/bolt and oil filter cover.
  • Avoid overtightening the oil drain bolt; always use a torque wrench for precision.
  • If your TE310 is equipped with a cooling fan, remember it can run even when the key is in the off position–keep away from the fan blades.
  • Oil changes are a good opportunity to perform a quick inspection of frame, engine mounts, and electrical wiring exposed during access.

Proper Oil Disposal

  • Transport used oil to your local motorcycle shop or automotive oil recycling center. Never dispose of oil in the trash or storm drains.

Conclusion

By following this Husqvarna TE310-specific oil change guide, you’ll help ensure long engine life and smooth power delivery every ride. For premium oil, filters, and all dirt bike maintenance needs, trust MotoSport.com.

Related Shopping Categories

Shop Motor Oil for a 2011 Husqvarna TE310 Dirt Bike.

Shop Oil Filters for a 2011 Husqvarna TE310 Dirt Bike.

Shop Oil Drain Pans for a 2011 Husqvarna TE310 Dirt Bike.

Shop Tools for a 2011 Husqvarna TE310 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2011 Husqvarna TE310 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.