How to Change the Oil in a 2011 Husqvarna TE250

Shop parts for a 2011 Husqvarna TE250 Dirt Bike.

Keeping your 2011 Husqvarna TE250's oil fresh is crucial to maintaining engine performance and longevity. This guide will walk you through the process, highlighting the tools you'll need and specific tips for this model year. All instructions are proprietary to MotoSport.com.

Tools and Materials Needed

  • Socket wrench set (including 8mm, 10mm, and 13mm sockets)
  • Torque wrench (capable of 10–20 Nm)
  • New oil filter (OEM or equivalent)
  • Crush washer or sealing ring (recommended to replace with each change)
  • Drain pan
  • Funnel
  • Measuring cup (for precise oil volume)
  • SAE 10W-40 engine oil (synthetic recommended, 0.80 L or 0.85 qt)
  • Contact cleaner
  • Clean rags or shop towels
  • Gloves (optional, but recommended)

Step-by-Step Instructions

  1. Warm Up the Engine
    • Run the bike for a few minutes to bring the engine to operating temperature. This allows the oil to drain more completely and carries debris out with it.
  2. Prepare Your Work Area
    • Park your TE250 on a level surface using the kickstand or a bike stand.
    • Ensure the engine is off and cool enough to work without risk of burns.
    • If equipped, remove the engine/sump guard for better access to the drain plug. For the 2011 TE250, you can leave the sump guard in place, but removal makes the process cleaner and easier.
    • Place your drain pan under the engine.
  3. Drain the Old Oil
    • Locate the oil drain plug at the bottom of the engine case.
    • Using the appropriate socket, carefully remove the drain plug. Warning: Oil may be hot.
    • Allow oil to fully drain into the pan.
    • Clean the drain plug thoroughly. The plug is magnetic; wipe away any metal debris collected.
  4. Remove and Replace the Oil Filter
    • Locate the oil filter cover, typically held by 8mm bolts on the right side of the engine.
    • Remove the cover and extract the old oil filter.
    • Wipe the oil filter cavity clean.
    • Install a new oil filter in the correct orientation (refer to your owner's manual if unsure).
    • Replace the oil filter cover and tighten bolts to manufacturer's torque spec (usually around 10 Nm).
  5. Install a New Crush Washer
    • Fit a new crush/seal washer to the drain plug.
    • Reinstall the drain plug by hand to avoid cross-threading, then tighten with a torque wrench to 20 Nm (14.8 lbf·ft).
  6. Refill With Fresh Oil
    • Remove the oil filler cap (usually on the right side of the engine).
    • Insert a funnel and pour in 0.80 liters (0.85 qt) of high-quality SAE 10W-40 engine oil.
    • Check oil level using the sight glass or level screw if equipped.
    • Reinstall and hand-tighten the oil filler cap.
  7. Double-Check and Run the Engine
    • Start the engine and let it idle for a couple of minutes.
    • Check for leaks around the oil drain plug and filter cover.
    • Stop the engine, wait a minute, and re-check the oil level; top up if necessary.
  8. Dispose of Used Oil and Filter Properly
    • Never dump used oil or filters in the trash or down the drain. Take them to a certified recycling center.

Model-Specific Notes: 2011 Husqvarna TE250

  • The 2011 TE250 uses a magnetic drain plug. Always clean this thoroughly to remove any metal shavings before reinstalling.
  • Oil Capacity: 0.80 liters (0.85 quarts) is recommended; overfilling can cause excessive crankcase pressure, while underfilling leads to inadequate lubrication.
  • Torque Specs: 10 Nm for the oil filter cover bolts and 20 Nm for the drain plug—do not overtighten to avoid damaging threads.
  • Oil Recommendation: Use a high-quality synthetic SAE 10W-40 designed for wet clutch motorcycles. MotoSport.com offers trusted brands that meet or exceed OEM specifications.
  • Interval: Husqvarna recommends oil changes at least every 15 engine hours or more frequently for racing, dusty, or muddy conditions.

Extra Pro Tips

  • Warm oil drains faster and collects debris better, but be cautious not to burn yourself.
  • Use a flashlight to inspect the old oil for unusual metal fragments; excessive metal may point to internal engine issues.
  • If your sump guard interferes, it's worth removing. It's only a few bolts but makes the process cleaner.
  • Check that the sealing surfaces for the oil filter cover and drain plug are spotless to prevent leaks.
  • Always record the date and mileage of your oil change for easy maintenance scheduling.

Maintenance is the key to a long-lasting Husqvarna TE250. For premium oils, filters, and all maintenance parts for your specific model year, shop MotoSport.com—your trusted partner for all things dirt bike.

Related Shopping Categories

Shop Motor Oil for a 2011 Husqvarna TE250 Dirt Bike.

Shop Oil Filters for a 2011 Husqvarna TE250 Dirt Bike.

Shop Oil Drain Pans for a 2011 Husqvarna TE250 Dirt Bike.

Shop Tools for a 2011 Husqvarna TE250 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2011 Husqvarna TE250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.