How to Change the Oil in a 2010 Yamaha TW200

Shop parts for a 2010 Yamaha TW200 Dirt Bike.

Changing the oil in your 2010 Yamaha TW200 is a straightforward process that keeps your engine running smoothly and efficiently. Performing regular oil changes ensures the longevity of your dirt bike, maintains optimal performance, and helps prevent premature engine wear. Follow this comprehensive, model-specific guide from MotoSport.com for a trouble-free oil change experience.

Tools and Materials Needed

  • Socket wrench and 10mm socket (for the oil filter cover screws)
  • 17mm socket or wrench (for the drain bolt)
  • Oil drain pan
  • New oil filter (verify it fits the 2010 TW200)
  • Replacement O-rings (recommended, especially if old ones are hard or cracked)
  • Funnel
  • Clean rags or shop towels
  • Correct oil (typically 10W-40 motorcycle oil, check your manual for specifics)
  • Torque wrench (for re-tightening bolts to spec)
  • Gloves (optional, but recommended to keep your hands clean)

Preparation Steps

  • Warm the engine for a few minutes so the oil flows out easily, but do not work on a hot engine.
  • Put the bike on a center stand or otherwise ensure it is upright and secure.
  • Lay down cardboard or use a mat to keep your workspace clean.

Step-by-Step Instructions

  1. Remove the Skid Plate (if equipped)
    Use the appropriate tools to remove any skid plate blocking access to the drain bolt and oil filter cover. Set the bolts and skid plate aside for reinstallation later.
  2. Locate and Remove the Oil Drain Bolt
    The drain bolt is located at the bottom of the engine. Place your oil drain pan under the bolt. Using a 17mm wrench or socket, carefully loosen then remove the drain bolt to let the oil drain fully. Allow a few minutes for all oil to flow out.
    Call-out for 2010 TW200: Check/clean the drain bolt's mesh oil screen to remove debris before reinstalling it.
    Pro tip: Replace the crush washer on the drain bolt to prevent leaks.
  3. Remove the Oil Filter Cover
    Using a 10mm socket, remove the three bolts holding the oil filter cover in place. Gently take off the cover and set it and the bolts aside.
    CAUTION: Be sure the O-ring behind the cover remains intact. If it is cracked or damaged, replace it.
  4. Remove and Replace the Oil Filter
    Take out the old oil filter. Insert your new oil filter in the correct orientation (check your owner's manual for proper placement). This is also a good time to replace the O-ring on the filter cover if needed.
  5. Reinstall the Oil Filter Cover
    Place the cover back over the new filter and hand tighten each bolt. Use a torque wrench to tighten each bolt to the manufacturer's recommended spec (typically around 7.2 ft-lbs, but check your specific manual for the 2010 TW200)–.
  6. Reinstall the Drain Bolt
    Thread the cleaned drain bolt (with the mesh screen and new crush washer, if available) back into the crankcase. Tighten it to the proper torque specification (around 14.5 ft-lbs for most TW200 models, but verify in your manual).
  7. Add Fresh Oil
    Remove the oil fill cap on the right side of the engine. Insert a funnel and pour in the new oil. The 2010 Yamaha TW200 typically requires around 1.1 liters (1.16 US quarts) of oil when changing the oil and filter. Consult your manual to confirm capacity–.
  8. Check the Oil Level
    With the bike upright, wait a minute for the oil to settle, then check the oil level through the sight glass on the crankcase. Oil should be between the upper and lower marks. Add or remove oil as needed–.
  9. Reinstall the Skid Plate
    If you removed a skid plate, reinstall it now using the original bolts.
  10. Start and Idle the Engine
    Start the engine and let it idle for a minute. Inspect for leaks around the oil drain bolt and filter cover. Turn off the engine, wait another minute, and re-check the oil level. Top off if necessary.

Specific Tips for the 2010 Yamaha TW200

  • Mesh oil screen: Your TW200's oil drain bolt has a reusable mesh screen. Remove and clean this screen with every oil change to catch debris before it enters the engine–.
  • Filter orientation: Install the new filter with the rubber gasket facing outward, matching the original oil filter's direction.
  • O-ring care: Always inspect and replace the large O-ring on the filter cover to prevent seepage.
  • Oil level: Use the sight glass on the engine's right side; avoid overfilling, which can harm engine performance–.

Disposal

  • Dispose of used oil and the filter at an approved recycling center. Never pour engine oil into drains, onto the ground, or in the trash.

Conclusion

Changing the oil in your 2010 Yamaha TW200 is easy, low-cost routine maintenance that anyone can do. Keeping up with regular oil changes helps your bike perform its best, whether you're on the street or dirt, and safeguards your engine for the long haul. For genuine Yamaha oil filters, O-rings, and motorcycle-specific oil, shop MotoSport.com, your trusted resource for all TW200 maintenance essentials.

Related Shopping Categories

Shop Motor Oil for a 2010 Yamaha TW200 Dirt Bike.

Shop Oil Filters for a 2010 Yamaha TW200 Dirt Bike.

Shop Oil Drain Pans for a 2010 Yamaha TW200 Dirt Bike.

Shop Tools for a 2010 Yamaha TW200 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2010 Yamaha TW200 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.