How to Change the Oil in a 2009 Husaberg FE450

Shop parts for a 2009 Husaberg FE450 Dirt Bike.

Changing the oil on your 2009 Husaberg FE450 is vital for engine health and optimal performance. Here’s a proprietary MotoSport.com guide covering the tools, process, and unique model insights to help you get the job done right.

Tools and Supplies Needed

  • Sockets and ratchet (primarily 13mm and 8mm for the drain plug, oil filter cover, and screen plug)
  • Torque wrench
  • Oil drain pan
  • Funnel
  • Clean rags
  • Contact or brake cleaner (for cleanup)
  • New oil filter
  • New copper or aluminum crush washer for drain plug
  • New engine oil (consult your owner’s manual; typically 10W-50 full synthetic, check for current recommendations and quantities)
  • Nitrile gloves (optional, but highly recommended)

Important Call-outs for the 2009 Husaberg FE450

  • This model features an oil screen and a cartridge-style oil filter. Both should be replaced/cleaned during every oil change.
  • The oil screen is located next to the oil drain plug on the right side of the engine inside a hex-head plug.
  • Always change the oil when the bike is at operating temperature to ensure old oil and contaminants drain completely. Use caution–hot oil can cause burns.
  • The engine uses a sight glass on the right crankcase for checking oil level; do not overfill.
  • Torque values are essential–over-tightening can damage the threads in the crankcase. Key torque for the drain plug: 20 Nm (14.7 ft-lbs).
  • Oil capacity for a full change (including filter): approx. 1.2L (1200 mL). Always verify with your service manual.

Step-by-Step Oil Change Procedure

  1. Warm Up the Engine
    • Start the engine and let it run for about 3-5 minutes. This ensures the oil is warm and flows freely, removing more contaminants.
  2. Position the Motorcycle
    • Place the bike upright and level, ideally on a bike stand to access the drain plug easily.
  3. Remove the Skid Plate (if equipped)
    • Remove any aftermarket or stock skid plate to access the drain and screen plugs.
  4. Drain the Oil
    • With gloves on, place the drain pan under the bike and carefully loosen and remove the main drain plug (right side, bottom of the engine).
      Warning: Hot oil drains quickly–keep your hands clear.
    • Let the oil fully drain for several minutes.
    • Remove the hex-head oil screen plug (next to the drain plug on the right side). Remove the oil screen from the plug for inspection.
  5. Clean and Inspect Components
    • Inspect the drain plug’s magnetic tip for metal shavings. Clean thoroughly.
    • Clean the oil screen with contact cleaner and inspect for debris or wear.
    • Replace crush washers/seal rings on both plugs with new ones.
  6. Replace the Oil Screen
    • Reinstall the cleaned oil screen back into its plug and fit the plug back in place. Do not over-tighten.
  7. Remove and Replace the Oil Filter
    • Locate and remove the oil filter cover (right side of engine, secured by two bolts).
    • Pull out the old oil filter and o-rings/gaskets (replace with new if supplied).
    • Prime the new oil filter by dipping it in clean oil, then install it into the filter housing. Replace the cover and tighten bolts to spec.
  8. Install Drain Plug and Screen Plug
    • Fit both plugs with new washers, thread them back into the engine, and torque each to 20 Nm.
  9. Add Fresh Oil
    • Remove the oil fill plug on top of the right engine case.
    • Using a funnel, pour in 1.2L of new oil–stop at 1.1L and check the sight glass. Top off as needed until oil is halfway to three-quarters up the window.
  10. Check for Leaks and Reinstall Skid Plate
    • Inspect underneath for leaks.
    • Reinstall the skid plate if removed.
  11. Final Oil Level Check
    • Start the engine, idle for 2-3 minutes, then shut it off and let it sit for 1-2 minutes.
    • Check oil level in the sight glass again; top off if necessary.

Owner Tips for the 2009 Husaberg FE450

  • Always use the recommended oil and OEM filters.
  • The FE450’s oil screen and magnet must be inspected every change; excessive debris could indicate deeper engine issues.
  • Thread pitch and aluminum case material mean threads can be easily stripped. Start each bolt and plug by hand before using tools.
  • Dispose of old oil and filter responsibly–take them to an auto parts shop or hazardous waste facility.

Consistent oil changes every 10–15 hours of riding keep your Husaberg running strong on trail, track, or adventure.

Proprietary to MotoSport.com — All Rights Reserved.

Related Shopping Categories

Shop Motor Oil for a 2009 Husaberg FE450 Dirt Bike.

Shop Oil Filters for a 2009 Husaberg FE450 Dirt Bike.

Shop Oil Drain Pans for a 2009 Husaberg FE450 Dirt Bike.

Shop Tools for a 2009 Husaberg FE450 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2009 Husaberg FE450 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.