How to Change the Oil in a 2006 Husqvarna WR250

Shop parts for a 2006 Husqvarna WR250 Dirt Bike.

Routine oil changes are crucial for the performance and longevity of your 2006 Husqvarna WR250. This comprehensive guide, exclusive to MotoSport.com, will walk you step by step through changing your engine oil, highlight any model-specific considerations, and ensure a smooth and mess-free process. Keeping your WR250 oil fresh will help your engine stay protected on and off the track.

Tools and Materials You’ll Need

  • Socket wrench with appropriate sockets (commonly 10mm and 12mm)
  • Allen/hex keys (if equipped with Allen bolts on skid plate)
  • Oil drain pan
  • New oil filter (OEM or compatible with the 2006 WR250)
  • Engine oil (SAE 10W-40 is commonly recommended; confirm with your owner’s manual)
  • Replacement crush washer or gasket (for drain plug, if needed)
  • Funnel (to help with refill)
  • Clean rags
  • Gloves (to protect your hands)

Preparation

  • Start up your bike and let it run for 2–3 minutes to warm up the oil. Warm oil drains better and more completely.
  • Put the bike on a stand or keep it vertical using a dirt bike lift, not on its kickstand; this helps ensure all oil drains out and you can check the level accurately later.

Step-by-Step Oil Change Instructions

  • Remove Skid Plate and Clean
    If equipped, remove the skid plate to access the drain bolt. The plate might be held by 8mm or 10mm bolts, or Allen bolts. Take care to keep track of hardware. Wipe away built-up dirt, especially around the drain bolt and oil filter cover, to prevent contaminating the engine when it’s open to the elements.
    WR250 tip: Pay particular attention to dirt around the frame guards, as debris can fall into the engine during disassembly.
  • Drain the Oil
    Locate the oil drain bolt, which is generally at the bottom of the engine case. Place your oil drain pan underneath.
    Use your wrench to loosen and remove the drain bolt. Be careful—hot oil may flow quickly. Let all oil drain out.
    Inspect the crush washer on the drain bolt. Replace if it looks worn or damaged to prevent future leaks.
  • Replace the Oil Filter
    Locate the oil filter cover (normally on the side of the engine). Remove the bolts securing the cover (commonly 8mm or 10mm). Gently remove the cover, keeping an eye out for any O-rings—don't lose them.
    Pull out the old oil filter. Inspect the cover gasket or O-ring; replace if damaged. Insert the new filter—make sure it seats properly.
    Reinstall the oil filter cover and torque the bolts to approximately 10 Nm, if you have a torque wrench.
  • Reinstall the Drain Plug
    Once oil has fully drained, reinstall the drain bolt (with a new crush washer if needed). Tighten it to approximately 20 Nm.
  • Refill with Fresh Oil
    Remove the oil fill cap (usually on the right side of the engine). Using a funnel, pour in fresh oil. For the 2006 WR250, add approximately 1.0–1.2 liters. If you’ve also replaced the oil filter, err on the higher side. Always confirm with your owner’s manual for exact capacity, as aftermarket parts may affect volume requirements.
  • Check Oil Level
    Reinstall the fill cap. Start and run the bike for 10–20 seconds. Shut off and allow oil to settle for a minute.
    Use the oil sight glass (if equipped) or check the dipstick or fill window (depending on specific model variant). The level should be between the upper and lower lines.

    Model-specific note: Some WR250s from this era have a sight glass, while others use a dipstick. Make sure your bike is held vertically—not on the side stand—when checking. Add oil as needed, but don't overfill.
  • Reinstall the Skid Plate and Frame Guards
    Replace and secure your skid plate and frame guards, ensuring all bolts are tight.
  • Final Check
    Run the engine again and check for leaks around the oil filter cover and drain plug. Wipe away any oil spills or residue.

Specific Call-outs for the 2006 Husqvarna WR250

  • This bike’s oil drain plug and filter are easily accessible, but dirt buildup is common with older models. Clean thoroughly before opening the engine.
  • Though most WR250s use the same drain bolt and filter location, always confirm bolt sizes before starting—Husqvarna made running changes in fasteners over the years.
  • Tip: Use an appropriately sized funnel and avoid cross-threading the oil fill cap, as plastic threads can strip easily after years of use.
  • If your bike has been sitting, oil may have pooled in different areas—run it briefly to return it to the sump before draining.

Disposal and Next Steps

  • Dispose of used engine oil responsibly—most auto parts stores and recycling centers accept it.
  • Mark your maintenance log with the oil change date and hours/miles; regular oil and filter changes will keep your WR250 performing at its best.

MotoSport.com offers a wide selection of oil filters, crush washers, and oils compatible with your 2006 Husqvarna WR250—stock up and keep your bike racing ready.

Related Shopping Categories

Shop Motor Oil for a 2006 Husqvarna WR250 Dirt Bike.

Shop Oil Filters for a 2006 Husqvarna WR250 Dirt Bike.

Shop Oil Drain Pans for a 2006 Husqvarna WR250 Dirt Bike.

Shop Tools for a 2006 Husqvarna WR250 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2006 Husqvarna WR250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.