How to Change the Oil in a 2001 Husqvarna TC570: A Complete Guide
Shop parts for a 2001 Husqvarna TC570 Dirt Bike.
Regular oil changes are crucial for keeping your 2001 Husqvarna TC570 performing at its best and extending its engine life. Unlike modern street bikes, dirt bikes like the TC570 often get ridden in rugged, dirty environments that can contaminate the oil quickly. This detailed MotoSport.com guide walks you step-by-step through a robust oil change, outlining required tools and specific tips for your model.
Tools and Supplies Needed
- OEM drain plug or a Bullet Proof Designs Oil Drain Tool (compatible with 2001 Husqvarna models)
- Socket wrench set (including 13mm and 8mm sockets)
- Oil filter (OEM or KTM PN 77038005000, or K&N PN KN-655)
- New engine oil (consult your owner's manual for type and volume; usually high-quality synthetic for dirt bikes)
- Drain pan or bucket
- Shop towels or rags
- Oil funnel
- Circlip pliers (for oil filter removal, if required)
- Replacement O-ring for oil filter cover (optional but recommended)
- Protective gloves
Specific TC570 Oil Change Notes
- Screened oil drain plug and engine oil screen plug: These components on the TC570 require cleaning during oil changes.
- Multiple drain points: Be aware that the TC570, like many Husqvarna big-bore four-strokes, has two engine oil drain points and an oil filter cavity.
- Oil filter type: Husqvarna often recommends specific part numbers, but K&N and KTM filter cross-references are widely accepted for the TC570.
Step-by-Step Instructions
-
Warm up the engine:
Let the engine idle for a few minutes to warm the oil. Warm oil drains more easily and completely, carrying away more contaminants. -
Prepare the workspace:
Park the TC570 on a level surface, preferably on a bike stand. Ensure your work area is ventilated and free from any sources of flame. Place your drain pan under the engine. -
Locate and remove oil drain plugs:
The TC570 has a main screened oil drain plug and an engine oil screen plug. Use your socket or end wrench to remove these plugs. Catch the draining oil in your pan. Be prepared for fast flow and possible splashing.- Tip: Using a Bullet Proof Designs oil drain tool (if available for your model) can make draining cleaner and faster, as it directs oil away from the skid plate and chassis.
-
Clean and inspect the drain plugs and screens:
Remove and clean the main oil drain plug and engine oil screen plug. Carefully wipe away sludge and check for metal shavings, which could indicate engine wear. Clean thoroughly and set aside. -
Access the oil filter:
Remove the oil filter cover by unscrewing the bolts with an 8mm socket. Be ready for more oil to drain when the cover is off; lean the bike left if needed to ensure a full drain.- Certain oil filters require circlip pliers for removal–double-check your filter type.
-
Replace the oil filter:
Fit a new oil filter (OEM, KTM, or K&N), ensuring it's properly oriented. Lightly oil the new O-ring before installation to guarantee a good seal. Carefully seat the filter cover to avoid pinching the O-ring or leaving gaps. -
Reinstall and tighten drain plugs and filter cover:
Install the clean drain plugs and torque them to spec–do not overtighten, as the threads in the cases are soft. Reattach the filter cover, ensuring a metal-on-metal seat and correct O-ring placement. -
Refill with new oil:
Use a funnel to pour in the recommended type and quantity of engine oil. Check your owner's manual for exact volume. -
Check for leaks and final checks:
Start the engine and let it idle for 2–3 minutes. Watch for leaks around the drain plugs and oil filter cover. Turn off the bike and let it sit for a minute, then check the oil level. Top off as needed. -
Dispose of old oil appropriately:
Transfer used oil to a sealable container and bring it to a recycling center–never dispose of it down a drain.
Model-Specific Callouts for the 2001 Husqvarna TC570
- Drain plug and oil screen: The TC570's design makes it easy to miss trapped oil, so be sure to rock the bike gently side to side, or briefly lean it left and right, to encourage complete draining.
- O-ring seating: Double-check O-ring condition and alignment when replacing the filter cover. A pinched or dry O-ring will cause leaks and could result in engine damage.
- Thread care: Both the drain plug threads and filter cover bolts screw into relatively soft aluminum. Always tighten to manufacturer spec with hand tools—never use air tools or excessive force.
Oil Change Frequency
- For optimal performance and engine life, change your oil every 5–10 hours of aggressive riding, or after every race/long dirt session.
Final Tips
- Label your next oil change mileage/hours on the frame with a marker or tag for easy maintenance tracking.
- Inspect drained oil for metal, milkiness (water contamination), or burnt smell: these can signal developing engine problems.
- Regular oil and filter changes are the simplest way to prevent expensive repairs and maximize the life of your 2001 Husqvarna TC570.
Related Shopping Categories
Shop Motor Oil for a 2001 Husqvarna TC570 Dirt Bike.
Shop Oil Filters for a 2001 Husqvarna TC570 Dirt Bike.
Shop Oil Drain Pans for a 2001 Husqvarna TC570 Dirt Bike.
Shop Tools for a 2001 Husqvarna TC570 Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2001 Husqvarna TC570 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.