How to Change the Oil in a 2000 Husqvarna CR50 Dirt Bike

Shop parts for a 2000 Husqvarna CR50 Dirt Bike.

Changing the oil regularly is critical to ensuring your 2000 Husqvarna CR50 runs smoothly and lasts for many years. This guide, created by MotoSport.com, provides specific instructions for the CR50 and highlights key points every owner should know.

Tools and Materials Needed

  • Socket wrench set (to remove drain plug)
  • Oil catch pan
  • Replacement engine oil (as specified in your owner's manual)
  • Funnel or syringe (for refilling oil)
  • Rags (for cleanup)
  • Torque wrench (to tighten drain plug to specification, typically 15 Nm – 11.06 ft-lb)
  • Gloves (optional, but recommended for safety)

Preparation

  • Start your engine and let it idle for a few minutes. Warming the engine helps the oil thin out and drain more completely.
  • Turn off the engine and let it cool briefly to avoid burns from hot oil.
  • Place the bike on a flat, stable surface in the vertical position using a bike stand.

Step-by-Step Guide

  1. Remove the Oil Filler Cap:
    • Locate and remove the oil filler cap on the engine. This allows air in, helping the oil flow out more quickly when drained.
  2. Place the Oil Pan:
    • Put the oil catch pan under the engine, directly below the oil drainage plug.
  3. Remove the Drain Plug:
    • Using the correct sized socket, remove the oil drainage plug (usually located at the lowest point of the engine case).
    • Allow the oil to drain completely into the pan. Be patient, as this can take a few minutes.
    • Be careful, as oil may still be hot.
  4. Inspect and Clean:
    • Check the plug and the area around it for metal shavings or debris. Clean any old oil residue from the drain plug and threads.
  5. Reinstall the Drain Plug:
    • Once the oil has drained, replace the plug and torque it to 15 Nm (11.06 ft-lb) as specified for the 2000 CR50. Do not overtighten.
  6. Refill with Oil:
    • Using a funnel or syringe, pour the recommended oil into the filler hole. Reference your owner’s manual for the specific oil type and capacity for the 2000 Husqvarna CR50.
    • As a general procedure:
      • Pour in about 600 milliliters (if uncertain, check for the model’s standard fill volume; older CR50s typically hold between 600 and 700 mL, but check owner's manual for specifics).
      • Allow oil to settle for a minute.
    • Check the oil level at the inspection screw or with a dipstick (if equipped):
      • Unscrew the level check screw and ensure oil just skims the hole's edge. If using a dipstick, the level should be at the "full" mark. Add more as needed, but do not overfill.
  7. Reinstall Filler Cap:
    • Put the oil filler cap back on and tighten.
    • Clean up any spilled oil with rags.
  8. Start and Idle the Engine:
    • Start the bike and let it run for a couple of minutes. Shut it off and check for leaks around the drain plug and filler cap.
    • Recheck your oil level and top up if needed.

Model-Specific Call-Outs for the 2000 Husqvarna CR50

  • Drain With Warm Engine: Always drain oil while the engine is warm for best results. This is particularly important for older models like the 2000 CR50 to ensure contaminants are removed with the old oil.
  • Oil Level Check: On the 2000 CR50, check the oil by undoing the check screw with the bike upright and on level ground. The oil should skim the edge of the level check hole. Topping off is best done with a syringe for accuracy.
  • Tighten Drain Plug to Specification: Over-tightening can strip threads in the relatively soft engine casing on older bikes. Use a torque wrench set to 15 Nm (11.06 ft-lb).
  • Oil Volume: Oil capacity may slightly vary due to residual oil in the engine. Begin with 600 mL and check before adding more—overfilling can cause foaming and premature engine wear. Always refer to the owner's manual if in doubt.
  • Dispose of Used Oil Properly: Take your used oil to a recycling center or auto parts store that accepts oil.

Final Tips

  • Record the date and hours/mileage of the oil change for your records.
  • Visually inspect your oil for discoloration or metal shavings, which can indicate engine wear or issues.
  • Keep spare drain plug washers on hand to replace if one gets damaged or lost.
  • For best performance, use only manufacturer-recommended oil types and weights.

For all your genuine Husqvarna and maintenance supply needs, MotoSport.com is your expert source. Keep your CR50 at peak performance with proper oil changes and regular maintenance.

Related Shopping Categories

Shop Motor Oil for a 2000 Husqvarna CR50 Dirt Bike.

Shop Oil Filters for a 2000 Husqvarna CR50 Dirt Bike.

Shop Oil Drain Pans for a 2000 Husqvarna CR50 Dirt Bike.

Shop Tools for a 2000 Husqvarna CR50 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2000 Husqvarna CR50 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.