How to Change the Coolant in a 2024 GAS GAS MC 350F: A MotoSport Guide
The 2024 GAS GAS MC 350F is renowned for its high-performance motor and racing capability, demanding diligent maintenance to ensure peak reliability. Regular coolant changes are a key part of that maintenance to prevent overheating and maximize engine life. This step-by-step MotoSport-exclusive guide will help you change the coolant efficiently and highlight important notes specific to your MC 350F.
What You'll Need
- Correct type of motorcycle coolant (consult your manual for the recommended type – typically a high-quality ethylene glycol-based coolant)
- Drain pan
- Ratchet and suitable socket
- Clean funnel
- Gloves and safety goggles
- Shop towels or rags
Before You Begin: Safety Tips
- Ensure the bike is completely cool before starting, as the cooling system can be under pressure and hot coolant can cause burns.
- Place the motorcycle on a stable, level surface using a stand for optimum access and safety.
Changing the Coolant: Step-by-Step
-
Remove the seat and radiator shrouds.
This allows clear access to the radiator cap and hoses. Use the appropriate tools carefully to avoid stripping screws or plastic mounting points. -
Find and remove the radiator cap.
Open the radiator cap slowly to relieve any residual pressure. The radiator cap is generally located on the right side. -
Locate the coolant drain bolt.
For the 2024 MC 350F, the coolant drain bolt is situated at the water pump cover on the right side of the engine.
Place your drain pan below this bolt to catch old coolant. -
Remove the coolant drain bolt and allow coolant to drain completely.
Use a ratchet and appropriate socket to remove the bolt. Clean any spilled coolant immediately, as it is toxic and can damage surfaces. -
Inspect and reinstall the drain bolt.
After draining, inspect the bolt and O-ring for wear or damage, replacing if necessary. Tighten the drain bolt to the manufacturer's torque spec to prevent leaks. -
Flush with clean water if necessary.
If the existing coolant was very dirty, pour in distilled water, reinstall the cap, run the engine briefly, then drain again. Repeat until clear. -
Refill with fresh coolant.
Using a funnel, pour the recommended coolant slowly into the top of the radiator until the fluid reaches just below the fill neck.
MC 350F system capacity is approximately 0.8 liters, but always verify visually to avoid overfilling. -
Bleed the cooling system.
Tip the bike side to side carefully to help any trapped air escape. You may need to open the radiator cap again after the engine runs and cools, topping off as required. Always check for air bubbles. - Reinstall the radiator cap, radiator shrouds, and seat.
-
Start the engine and check for leaks.
After warming the bike, inspect the drain bolt and hose connections for leaks. Verify the coolant remains at the proper level after cooling.
Important Notes for the 2024 GAS GAS MC 350F Owner
- This model uses a high-pressure cooling system for optimal off-road performance. Never use automotive coolant with silicates, as these can damage the pump and seals.
- The radiator is susceptible to external debris – regularly inspect and gently clean the radiator fins for the best cooling efficiency.
- Use of distilled water for topping off is preferred if premixed coolant is not available, but do not substitute it for the correct coolant over the long-term.
- Monitor the coolant reservoir and radiator level more frequently during race and hot-weather riding, as this engine operates at higher temperatures under load.
- If you notice persistent overheating or rapid coolant loss, inspect for hose leaks, a faulty radiator cap, or possible water pump issues.
Caring for your 2024 MC 350F's cooling system ensures maximum engine health and serious power delivery whenever you ride. For genuine replacement parts, fresh coolant, and maintenance gear tailored to your bike, MotoSport has you covered.
Related Shopping Categories
Shop Radiator Hoses for Your Ride
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.