How to Change the Coolant in a 2022 Sherco 300 SE FACTORY

Shop parts for a 2022 Sherco 300 SE FACTORY Dirt Bike.

Proper cooling system maintenance is essential for keeping your 2022 Sherco 300 SE FACTORY running at peak performance on every ride. This step-by-step guide makes coolant changes straightforward, and highlights important things every owner should know about this advanced off-road machine.

Why Changing Coolant Matters

Fresh coolant ensures efficient heat transfer and system reliability. The 300 SE FACTORY uses a high-performance liquid cooling system tailored to its fuel-injected 2-stroke engine. Only use high-quality, manufacturer-approved coolant–never plain water–to prevent corrosion, overheating, or damage to expensive internal components.

What You Will Need

  • Minerva Perma Universal D 4 (or equivalent, rated to at least -25°C)
  • Catch pan for old coolant
  • Basic hand tools (socket set, screwdrivers)
  • Torque wrench (optional, but recommended for proper tightening)
  • Shop rags for cleanup

Step-by-Step Coolant Change Instructions

  1. Prepare the Bike:
    • Let the engine cool completely before starting to prevent burns.
    • Support the motorcycle upright and level.
  2. Access the Cooling System:
    • Remove the seat and fuel tank as needed for easier radiator access.
  3. Drain Old Coolant:
    • Locate the radiator cap and carefully remove it to relieve any pressure.
    • Position your catch pan beneath the water pump area on the right side of the engine.
    • Remove the coolant drain screw (referenced as screw A in the factory manual) from the water pump cover to allow coolant to drain fully into your pan. Make sure to open the bleed screw on the left radiator if available–this helps ensure complete draining.
    • Avoid spilling coolant on painted surfaces, and dispose of used fluid at an approved collection center.
  4. Check System Components:
    • Visually inspect radiator hoses for cracks, hardening, or leaks. Squeeze hoses to check for flexibility.
    • Check hose clamps and radiator for damage or bent fins–repair as needed.
  5. Refill with Fresh Coolant:
    • Install and tighten the drain screw using a new sealing washer if required (8 Nm torque for radiator bleed screw, per manual instructions).
    • Fill the radiator slowly at the cap opening with fresh coolant, allowing air to escape via the radiator bleed screw on the left side until no more bubbles emerge, then tighten the bleed screw.
    • Continue adding coolant until it reaches the level line (approx. 1.1 liters total capacity). Do not overfill.
  6. Bleed the System:
    • With the bike on the side stand, gently rock it side to side to help any residual air escape. Top off coolant as needed.
    • Replace the radiator cap securely.
  7. Start and Check:
    • Start the engine and let it idle. Monitor coolant level in the expansion tank and check for leaks.
    • Allow the engine to reach operating temperature and check the coolant level again. Add more if necessary.

Model-Specific Tips for the 2022 Sherco 300 SE FACTORY

  • This model employs a powerful closed-cartridge KYB suspension and a factory-tuned engine, so consistent cooling is vital for optimum performance and reliability.
  • A properly bled cooling system prevents vapor lock and potential engine overheating.
  • Always use manufacturer-specified gasket washers for drain and bleed screws to avoid leaks after service.
  • The 300 SE FACTORY's compact frame means component access can be tight; take your time during disassembly and reassembly.
  • If performing advanced service (like replacing the water pump seal), refer to factory torque specs and sequence for critical fasteners for a leak-free result.

When to Replace Coolant

For maximum protection, replace coolant at least once a year or after heavy, muddy use. Inspect fluid color–if it's cloudy, rusty, or contains debris, replace immediately.

Environmental Responsibility

Never dump coolant; protect the environment by taking used fluids to a certified recycling facility.

Final Check

Take a short test ride after the service, then recheck coolant level and system for leaks. Keeping your 2022 Sherco 300 SE FACTORY's cooling system in top shape ensures you can focus on your ride, not your radiator.

Related Shopping Categories

Shop Radiators for a 2022 Sherco 300 SE FACTORY Dirt Bike.

Shop Coolant for a 2022 Sherco 300 SE FACTORY Dirt Bike.

Shop Temperature Sensors for a 2022 Sherco 300 SE FACTORY Dirt Bike.

Shop Tools for a 2022 Sherco 300 SE FACTORY Dirt Bike.

Shop Radiator Hoses for a 2022 Sherco 300 SE FACTORY Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.