How to Change the Coolant in a 2022 Honda CRF300L RALLY ABS

Shop parts for a 2022 Honda CRF300L RALLY ABS Dirt Bike.

Proper coolant maintenance ensures consistent engine temperature and longevity, especially for the 2022 Honda CRF300L RALLY ABS—known for its dual-sport capability and advanced ABS system. Follow this step-by-step process to change your coolant safely and efficiently, keeping in mind spec details unique to this model.

What You Will Need

  • 5mm Hex key (Allen wrench)
  • Phillips head screwdriver
  • Drain pan
  • Funnel
  • Pro Honda HP Coolant or equivalent high-quality, silicate-free ethylene glycol coolant with corrosion inhibitors
  • Paper towels/rags
  • Torque wrench (optional, but recommended)
  • Replacement crush washer (recommended for drain plug)

Preparation

  • Ensure the engine is completely cold before starting the procedure to avoid burns and pressurized coolant escape.
  • Position the bike upright on level ground–a center stand or maintenance stand is ideal.

Step 1: Remove Side Panels and Access the Radiator

  • On the right side, use a 5mm hex key to remove the mounting screws holding the fairing.
  • Disconnect the Velcro gently and locate the plastic push pins near the radiator–depress the center and gently remove the pins.
  • Pull the fairing panel away to fully expose the radiator and reservoir tank.

Step 2: Drain the Old Coolant

  • Locate the radiator drain bolt at the base of the water pump (right side of engine).
  • Position the drain pan beneath the bolt.
  • Carefully remove the radiator cap (using a Phillips screwdriver for the retainer screw if needed).
  • Loosen and remove the radiator drain bolt–allow all coolant to fully drain.
  • Remove the reservoir tank cap and drain its contents.

Step 3: Inspect and Reinstall the Drain Bolt

  • Check condition of the crush washer–replace if worn or damaged.
  • Clean threads, then reinstall and hand-tighten the drain bolt. Use a torque wrench set to manufacturer specification for extra security.

Step 4: Fill with New Coolant

  • Using a funnel, pour Pro Honda HP Coolant (or equivalent, silicate-free, ethylene glycol based coolant) slowly into the radiator until full.
  • Fill the reservoir tank to the "Full" mark while the bike is vertical.

Step 5: Bleed Air & Check Levels

  • Reinstall the radiator cap and reservoir cap. Reattach any removed panels and fasten all screws and clips securely.
  • Start the engine and let it idle with the radiator cap on for several minutes to warm up. Watch the temperature gauge light and inspect for leaks.
  • Turn the engine off and allow it to fully cool.
  • Open the radiator cap and check coolant level–top off as needed. Double-check the reservoir tank, too.

2022 CRF300L RALLY ABS Special Considerations

  • ABS variant brakes: Avoid spilling coolant onto the ABS sensor or wiring; wipe up immediately if contact occurs.
  • Factory recommendation: Use only approved silicate-free ethylene glycol coolant to protect gasket and aluminum radiator lifespan.
  • Coolant interval: Honda recommends changing the coolant every 2 years or as indicated by the maintenance schedule.

Final Checks

  • Inspect for any coolant leaks.
  • Double-check that all panels and bolts are secure.
  • Recycle the old coolant responsibly according to your local laws.

Stay on top of routine maintenance for the 2022 CRF300L RALLY ABS–your dual-sport adventures depend on top cooling performance, especially during long rides and hot weather.

Related Shopping Categories

Shop Radiators for a 2022 Honda CRF300L RALLY ABS Dirt Bike.

Shop Coolant for a 2022 Honda CRF300L RALLY ABS Dirt Bike.

Shop Temperature Sensors for a 2022 Honda CRF300L RALLY ABS Dirt Bike.

Shop Tools for a 2022 Honda CRF300L RALLY ABS Dirt Bike.

Shop Radiator Hoses for a 2022 Honda CRF300L RALLY ABS Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.