How to Change the Coolant in Your 2010 Husqvarna TE310
Shop parts for a 2010 Husqvarna TE310 Dirt Bike.
Changing the coolant in your 2010 Husqvarna TE310 is a straightforward but vital maintenance task that ensures your high-performance off-road bike runs at the correct temperature during demanding rides. Follow this MotoSport-exclusive guide for a safe and effective coolant replacement tailored specifically to your TE310’s unique design.
What Makes the 2010 TE310 Unique?
- High-Performance Engine: The TE310 is known for its robust four-stroke, 302cc engine, which works hard in hot conditions–making efficient cooling a priority.
- Cast Aluminum Chassis: The frame design aids in weight savings, but requires careful handling when draining fluids to avoid contact with the frame and wiring.
- Radiator Fan Feature: The TE310 radiator fan can activate even when the ignition is switched off. Keep clear of the fan at all times to avoid injury.
What You’ll Need
- Fresh motorcycle coolant (0.9 liters recommended for the TE310)
- Catch pan or suitable container
- Screwdrivers or pliers (for hose clamps)
- Gloves and protective eyewear
- Funnel (for refilling)
- Shop rags for drips
Step-by-Step Coolant Change
-
Preparation:
- Ensure the engine is completely cool before starting. Never open the radiator cap when the engine is hot to prevent scalding.
- Place your bike on a level stand to keep it upright during the process.
-
Drain the Old Coolant:
- Position a catch pan on the left side of the cylinder, directly under the lower radiator hose.
- Loosen the clamp on the hose and carefully detach it from the engine. Coolant will begin to flow out. Allow it to drain completely.
- SLOWLY open the right-hand radiator cap to speed the draining and allow air in while fluid drains.
- Gently lean the motorcycle to the left to encourage full drainage. Once flow stops, refit the hose and clamp securely.
-
Refilling with New Coolant:
- Double-check that all hoses are properly secured.
- Pour fresh coolant slowly into the radiator until full (0.9 liters for TE310).
- Start the engine and allow it to run at idle to circulate coolant through the system. Watch for air bubbles escaping at the filler neck.
-
Eliminate Air Bubbles:
- With the engine warm, gently rock the bike side to side and top off as air is purged. Replace the radiator cap when fluid remains at the neck and no bubbles appear.
- Let the bike cool down, then recheck the coolant level and top off as necessary.
-
Inspect Hoses and Clamps:
- Examine all hose connections for leaks and proper tightness.
- Replace any hoses showing signs of cracking, swelling, or hardening, as these are common issues on older TE310 models and can lead to leaks and potential engine seizure.
Important Tips for TE310 Owners
- Always use the coolant type specified by the manufacturer for optimal engine protection and cooling.
- The radiator fan can activate even with the ignition off. Keep fingers and tools clear at all times to avoid accidental injury.
- Maintain regular schedules for checking and replacing coolant hoses to ensure reliability on the trail.
- If you notice repeated coolant loss or overheating, inspect for hose leaks and consult a mechanic to avoid costly repairs.
Be diligent with your maintenance, and your 2010 Husqvarna TE310 will stay ready for every ride.
Related Shopping Categories
Shop Radiators for a 2010 Husqvarna TE310 Dirt Bike.
Shop Coolant for a 2010 Husqvarna TE310 Dirt Bike.
Shop Temperature Sensors for a 2010 Husqvarna TE310 Dirt Bike.
Shop Tools for a 2010 Husqvarna TE310 Dirt Bike.
Shop Radiator Hoses for a 2010 Husqvarna TE310 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.