Bleeding the Brakes on a 2025 Honda Africa Twin 1100 DCT

Shop parts for a 2025 Honda Africa Twin 1100 DCT Motorcycle.

The 2025 Honda Africa Twin 1100 DCT uses hydraulic disc brakes at both ends and is equipped with ABS. The DCT gearbox does not change the brake bleeding job; you are working only with the brake hydraulic circuits. This guide covers a routine fluid flush and air removal through the caliper bleeders. If air has entered the ABS unit itself, the job moves beyond a normal garage bleed and should go to a shop with the appropriate diagnostic equipment.

What a Brake Bleed Does on This Africa Twin

Bleeding pushes fresh fluid through the master cylinder, lines, and calipers while carrying old fluid and trapped air out through the bleeder valves. On the Africa Twin 1100 DCT, the front and rear hydraulic circuits are serviced as separate bleed jobs. A routine bleed at the calipers is the normal way to refresh fluid and remove air that entered at a caliper, line, or master cylinder. It is not a substitute for an ABS-unit bleed if the system has been run dry or opened at the ABS hardware.

Brake fluid absorbs moisture over time. That moisture lowers the fluid’s boiling point and can contribute to brake fade under hard, repeated use. Even when the lever and pedal feel normal, many riders refresh brake fluid on a regular schedule as preventive maintenance. A bleed is also due whenever the system has been opened for new lines, caliper service, or master cylinder work.

When the Africa Twin Needs a Bleed

Pay attention to a spongy or soft front lever or rear pedal, a lever that now pulls closer to the grip than it used to, or a pedal that feels vague. Dark or cloudy fluid in the reservoir is another sign that fresh fluid is overdue. Any repair that opened the hydraulic system should be followed by a bleed before the bike is ridden normally. If the lever slowly sinks while you hold steady pressure, air or a leak is likely present, and the bike should not be ridden until the cause is corrected.

Tools and Supplies to Stage Before You Start

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve
  • Clear tubing that fits snugly over the bleeder valve
  • A catch bottle for old fluid
  • Rags or shop towels
  • A syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver or driver that fits the reservoir cap screws

A one-way check-valve bleeder or a vacuum bleeder can make the job easier for one person, but the basic lever-and-bleeder method works with the items above.

Preparing the Bike and Protecting Sensitive Surfaces

Support the Africa Twin securely upright on a stand so it cannot tip while you are working at the bars or the rear caliper. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If fluid spills, wipe it up immediately and rinse the area with water. Keep the reservoir cap and diaphragm clean and set them where they will not pick up grit.

Bleeding the Front Brake Circuit

Work with the front reservoir level and keep an eye on its fluid level throughout the job. If your bike has more than one front caliper, treat each caliper as its own bleed point and finish one before moving to the other. When a system has a clear farthest caliper from the master cylinder, start there.

  1. Open the front reservoir and use a syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry.
  2. Refill the reservoir with fresh fluid of the type marked on the cap.
  3. Attach the clear tubing to the front caliper bleeder and route the other end into the catch bottle.
  4. Squeeze and hold the front lever.
  5. Open the bleeder about a quarter turn to let fluid and air escape.
  6. Close the bleeder before releasing the lever.
  7. Release the lever, then repeat the squeeze-hold-open-close sequence until fresh, clean, bubble-free fluid comes through the tube.
  8. Keep topping off the reservoir throughout so it never runs low enough to draw air into the system.
  9. If there is a second front caliper, repeat the same sequence at that caliper.

Bleeding the Rear Brake Circuit

The rear circuit uses the same basic method, but you operate the rear pedal instead of the front lever. Confirm the rear reservoir is filled to its level marking before you begin, and keep it topped off as fluid is drawn through the system.

  1. Remove most of the old fluid from the rear reservoir without letting it run dry.
  2. Refill with fresh fluid of the type marked on the cap.
  3. Fit the clear tubing over the rear caliper bleeder and route it into the catch bottle.
  4. Press and hold the rear pedal.
  5. Open the bleeder about a quarter turn.
  6. Close the bleeder before releasing the pedal.
  7. Release the pedal and repeat until the fluid in the tube is clean and free of bubbles.
  8. Check the reservoir level often and top it off before it gets low.

Finishing, Testing, and Knowing When to Stop

When the fluid runs clean at both ends, tighten each bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid. Check for leaks at the bleeder valves and at the banjo fittings. The front lever and rear pedal should feel firm and consistent, not spongy, and should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging, then test the brakes at low speed in a safe area before riding normally.

If the lever or pedal will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid is leaking from the master cylinder or caliper, stop and diagnose the problem. A reservoir that ran dry, a disconnected ABS line, or any work that disturbed the ABS unit can leave air where a hand bleed will not remove it. In those cases, have a shop perform the ABS bleed with the proper equipment rather than riding with a brake system that is not fully firm.

Related Shopping Categories

Shop Brake Fluid for a 2025 Honda Africa Twin 1100 DCT Motorcycle.

Shop Brake Lines for a 2025 Honda Africa Twin 1100 DCT Motorcycle.

Shop Brake Pads for a 2025 Honda Africa Twin 1100 DCT Motorcycle.

Shop Stands for a 2025 Honda Africa Twin 1100 DCT Motorcycle.

Shop Brake Tools for a 2025 Honda Africa Twin 1100 DCT Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.