Bleeding the Brakes on a 2025 Honda Africa Twin 1100 Adventure Sports ES

Shop parts for a 2025 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Know the System Before You Open It

The 2025 Honda Africa Twin 1100 Adventure Sports ES uses hydraulic disc brakes at both ends and is equipped with ABS. That means you have a front lever circuit and a rear pedal circuit to service, and both use brake fluid rather than a cable. The ABS hardware does not change the basic caliper-bleeding process when you are simply refreshing fluid or removing air that entered at a caliper or line. It does matter if the reservoir has run dry or the ABS unit or its lines have been disconnected: air can then be trapped inside the ABS unit, and a normal bleed at the calipers may not remove it. In that case, stop and have a shop with the appropriate diagnostic equipment complete the job.

Why and When to Bleed

Brake fluid absorbs moisture over time. That lowers its boiling point and can make the brakes fade under hard, repeated use, even if the bike feels fine on a short ride. Bleeding also removes air, which is compressible and shows up as a soft or spongy lever or pedal. Consider a bleed when the front lever pulls closer to the grip than it used to, when the rear pedal feels vague, when the fluid in either reservoir looks dark or cloudy, or after any work that opened the hydraulic system—new lines, caliper service, or master cylinder work. Many riders also refresh fluid on a regular schedule as preventive maintenance.

Tools and Supplies

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve snugly
  • Clear tubing that fits tightly over the bleeder
  • A catch bottle for used fluid
  • Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir
  • The correct driver for the reservoir cap screws
  • Optional: a one-way check-valve bleeder or vacuum bleeder to make one-person work easier

Use only fresh fluid from a sealed container. Do not guess at the fluid type; read the reservoir cap. Have enough rags on hand to wipe up spills immediately, because brake fluid damages paint and plastic on contact.

Set Up Safely

Support the Africa Twin securely upright on a stand so it cannot tip while you work. Turn the handlebars until the front reservoir sits level before you open it. Cover the tank area, bodywork, instrument cluster, and any painted surfaces around the reservoirs with rags. If fluid touches paint or plastic, wipe it up at once and rinse the area with water. Work in a well-ventilated area and keep used fluid away from children and pets.

Step-by-Step Bleeding Procedure

  1. Open the reservoir for the circuit you are bleeding and remove most of the old fluid with a syringe or turkey baster. Do not let the reservoir run dry.
  2. Refill with fresh fluid of the type marked on the cap, leaving room for the diaphragm and cap to seat.
  3. Fit the clear tubing over the bleeder valve and route the other end into the catch bottle with a little fluid in the bottom.
  4. For the front, squeeze the lever and hold it. For the rear, press and hold the pedal. Keep steady pressure on it.
  5. Open the bleeder about a quarter turn. Fluid and any air will flow through the tube. Close the bleeder before you release the lever or pedal.
  6. Release the lever or pedal, then repeat the squeeze-hold-open-close-release cycle. Check the reservoir often and top it off so it never draws air.
  7. Continue until the fluid coming through the tube is clean and free of bubbles. If your bike has two front calipers, bleed each one in turn. As a general practice, start with the caliper farthest from the master cylinder.
  8. Repeat the same process on the rear circuit if you are bleeding both ends. Keep the reservoir topped off throughout.

Finishing and Leak Checks

When clean, bubble-free fluid comes through, close the bleeder snugly. Do not overtighten it; snug is enough to seal. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe away any spilled fluid. Check the bleeder and the banjo fittings at the master cylinder and caliper for weeping or drips. A dry fitting after several firm lever or pedal applications is what you want to see.

Test Before Riding

The lever and pedal should feel firm and consistent, not spongy, and they should not slowly sink while you hold steady pressure. Spin each wheel and confirm the brakes are not dragging. Ride at low speed in a safe area and test the brakes gently before riding normally. If anything feels soft, inconsistent, or weaker than before, do not ride the bike until the problem is resolved.

When to See a Shop

If the lever or pedal will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid leaks from the master cylinder or caliper, stop and have the system inspected. The same applies if the reservoir ran dry, if the ABS unit or its lines were disconnected, or if you are unsure whether air entered the ABS hardware. Those situations can require a dealer-level procedure or diagnostic tool that is beyond a normal caliper bleed.

Related Shopping Categories

Shop Brake Fluid for a 2025 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Shop Brake Lines for a 2025 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Shop Brake Pads for a 2025 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Shop Stands for a 2025 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Shop Brake Tools for a 2025 Honda Africa Twin 1100 Adventure Sports ES Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.