How to Bleed the Brakes on a 2020 Honda Africa Twin 1100 DCT
Shop parts for a 2020 Honda Africa Twin 1100 DCT Motorcycle.
What You Are Working With on This Bike
The 2020 Honda Africa Twin 1100 DCT uses hydraulic disc brakes at both ends, and the system is ABS-equipped. That means you have a front master cylinder fed by the lever on the right bar, a rear master cylinder operated by the pedal on the right side, and calipers at each wheel with bleeder valves built into them. The front end carries dual discs, so there are two front calipers to service rather than one. Because ABS is part of the package, a routine flush through the caliper bleeders is a normal garage job — but if air has been allowed into the ABS modulator itself, the story changes, and that is covered further down.
Nothing about the DCT gearbox changes the brake bleeding process. The transmission is separate from the hydraulic brake circuit, so you can treat this exactly like any other ABS-equipped twin-disc street bike when you are at the bleeder.
When the Brakes Need Bleeding
Air in a hydraulic system is compressible, and fluid is not. That difference is what you feel through the lever and pedal. A front lever that feels soft, spongy, or that travels closer to the grip than it used to is the classic symptom. The same goes for a rear pedal with a vague, mushy feel or excessive travel before it bites. A lever that firms up when you pump it and then goes soft again while you hold it is a strong sign that air is still working its way through.
Fluid condition matters just as much as feel. Pop the reservoir cap and look at the fluid — if it is dark, cloudy, or has visible sediment, it is past its useful life. Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. Moisture lowers the fluid's boiling point, and on a heavy adventure bike that gets loaded down and ridden hard through mountain passes, that can translate into fade when you need the brakes most. Many riders simply refresh the fluid on a regular interval rather than waiting for a symptom.
You also need to bleed after any work that opened the hydraulic circuit: new brake lines, a caliper rebuild or replacement, master cylinder service, or any moment where the reservoir ran low enough to pull air in.
Tools and Supplies to Gather First
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different specification.
- A box-end wrench that fits the bleeder valve snugly — a six-point box end is far less likely to round the bleeder than an open end.
- Clear tubing that fits tightly over the bleeder nipple, long enough to reach your catch bottle.
- A clear catch bottle so you can watch the fluid and any bubbles coming through.
- Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Optional but genuinely helpful for a solo job: a one-way check-valve bleeder or a vacuum bleeder.
Setting Up Before You Open Anything
Get the bike secure and upright on a stand so it cannot tip while you are leaning on the lever. For the front circuit, turn the handlebars until the front reservoir sits level — a reservoir that is tilted will spill the moment you remove the cap. Then drape rags over the tank area, the plastics, the instrument cluster, and anything painted below the reservoir and calipers. Brake fluid attacks paint and many plastics on contact, and a drip you did not notice can leave a permanent mark. If a spill does happen, wipe it up immediately and rinse the area with water rather than waiting until the end of the job.
The Bleeding Procedure, Front and Rear
Work through the front circuit first, then repeat the same sequence at the rear. On a dual-disc front end, bleed one caliper at a time and finish it completely before moving to the other. As a general practice, start with the caliper farthest from the master cylinder in terms of hydraulic path, then do the closer one.
- Remove the reservoir cap and diaphragm. Use the syringe or baster to draw most of the old fluid out of the reservoir, but leave enough at the bottom that you are not pulling air into the master cylinder port.
- Top the reservoir up with fresh fluid from the sealed container.
- Push the clear tubing onto the bleeder valve and route the other end into the catch bottle, with the bottle positioned so the tube end stays submerged.
- Squeeze the front lever and hold it firm, or press and hold the rear pedal. Do not release it yet.
- Open the bleeder about a quarter turn with the box-end wrench. Fluid and air will push out through the tube. Watch the tube, not the reservoir, while it flows.
- Close the bleeder before you release the lever or pedal. Releasing with the bleeder open draws air straight back into the caliper, which is the single most common mistake in this job.
- Release the lever or pedal slowly, then check the reservoir level and top it off. Repeat the squeeze–hold–open–close–release cycle until the fluid coming through the tube runs clean and free of bubbles.
- Keep the reservoir topped up throughout. If it runs dry, you will pull air into the master cylinder and possibly into the ABS unit, and you will be starting over.
- Move to the second front caliper if your bike has one, then repeat the entire sequence at the rear caliper using the pedal.
Finishing Up and Checking Your Work
Once clean, bubble-free fluid is flowing, close the bleeder and tighten it snugly with the box-end wrench. Snug is the goal — do not lean on it, because overtightening can damage the seat and create a leak. Refill the reservoir to the level marking on the body, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder valves and the banjo fittings at the master cylinder and calipers for any weeping or dampness.
Testing Before You Ride
With the bike still stationary, pull the front lever and press the rear pedal several times. Both should feel firm and consistent, and neither should slowly sink toward the grip or the floor while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then take the bike to a quiet, safe area and test the brakes at low speed before riding normally.
Troubleshooting and When to Stop
If the lever will not firm up after several full bleeding cycles, if it only firms up when you pump it, or if bubbles keep appearing no matter how long you bleed, stop and reassess. Fluid leaking from the master cylinder or a caliper means a seal issue that bleeding will not fix. And because this Africa Twin has ABS, any situation where the reservoir ran dry, the ABS unit was disturbed, or the lines to it were opened may leave air trapped where a hand bleed cannot reach it — that requires a dealer-level procedure or diagnostic tool. In any of those cases, hand the bike to a shop rather than riding it with a brake system you are not sure of.
Related Shopping Categories
Shop Brake Fluid for a 2020 Honda Africa Twin 1100 DCT Motorcycle.
Shop Brake Lines for a 2020 Honda Africa Twin 1100 DCT Motorcycle.
Shop Brake Pads for a 2020 Honda Africa Twin 1100 DCT Motorcycle.
Shop Stands for a 2020 Honda Africa Twin 1100 DCT Motorcycle.
Shop Brake Tools for a 2020 Honda Africa Twin 1100 DCT Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.