Bleeding the Brakes on a 2019 Kawasaki ER400 ABS / Z400

Shop parts for a 2019 Kawasaki ER400 - Z400 ABS Motorcycle.

What You're Working With on This Bike

The 2019 Kawasaki ER400 ABS — the model most riders know as the Z400 — runs hydraulic disc brakes at both ends, with an anti-lock braking system plumbed into the circuit. That gives you two independent hydraulic systems to service: a front system fed by the lever on the right handlebar, and a rear system fed by the pedal on the right footpeg. Each has its own master cylinder, its own reservoir, and its own bleeder valve down at the caliper. The two are not linked, so you can bleed them one at a time in whatever order suits you.

Because this machine carries ABS, one caveat applies from the first step to the last. A normal flush pushed through the caliper bleeder is a perfectly reasonable garage job. But if air has been drawn into the ABS unit itself — the reservoir ran dry while you were working, or the ABS block or its lines were disconnected — the modulator may need a dealer-level procedure or diagnostic tool to purge properly. If that has happened, stop and take the bike to a shop rather than pumping away at the lever hoping for the best.

How to Tell a Bleed Is Due

The classic warning is feel. A lever that has gone soft, or that now travels noticeably closer to the grip than it used to, usually means air or moisture has worked its way into the system. The rear pedal can go the same way, feeling vague or spongy underfoot. Pop the reservoir cap and look at the fluid: fresh brake fluid is clear and pale, while fluid that has been in service for a couple of seasons turns dark, cloudy, or tea-colored.

Even without symptoms, brake fluid absorbs moisture from the air over time. That moisture lowers the fluid's boiling point, and a fluid that boils under hard, repeated braking creates gas in the lines — which is exactly the spongy, fading feel you are trying to avoid. Many riders simply refresh the fluid on a regular interval as preventive maintenance. A bleed is also mandatory after any work that opened the hydraulic circuit: new lines, a caliper rebuild, or master cylinder service.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container — once a container is opened, it starts absorbing moisture, so use new stock
  • A box-end wrench that fits the bleeder valve snugly
  • A length of clear tubing that fits tightly over the bleeder nipple
  • A small catch bottle for the old fluid
  • Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir
  • The correct driver for the reservoir cap screws
  • Optional but helpful: a one-way check-valve bleeder or a vacuum bleeder, which makes a one-person job much less fiddly

Setting Up Safely

Get the bike held securely upright on a stand so it cannot tip while you are leaning on the lever. For the front circuit, turn the handlebars until the reservoir on the bar sits level — an angled reservoir will spill as soon as the cap comes off. Before opening anything, drape rags over the tank area, the plastics, the instrument cluster, and anything else below the reservoir. Brake fluid attacks paint and many plastics on contact, so any drip needs to be wiped up immediately and the area rinsed with water.

The Bleeding Procedure

  1. Remove the reservoir cap and diaphragm. Use the syringe or baster to draw most of the old fluid out of the reservoir, but leave enough at the bottom that you are not pulling air into the master cylinder port.
  2. Top the reservoir up with fresh fluid from your sealed container.
  3. Push the clear tubing onto the bleeder valve and route the other end into the catch bottle, with the bottle positioned so the tube's end stays submerged in fluid if possible.
  4. Squeeze the lever (or press the pedal) and hold it steady. With pressure held, crack the bleeder about a quarter turn with the box-end wrench. Fluid and any trapped air will push out through the tube.
  5. Close the bleeder before you release the lever or pedal. Releasing with the bleeder open draws air straight back into the caliper, undoing your work.
  6. Repeat the squeeze–hold–open–close–release cycle, checking the reservoir level every few strokes and topping it off so it never runs low enough to gulp air.
  7. Keep going until the fluid coming through the tube is clean and fresh and you see no more bubbles. On a bike with two front calipers, bleed each caliper separately, one at a time; the general practice is to start with the caliper farthest from the master cylinder and work toward the closest.
  8. Move to the other circuit and repeat the whole process with its own reservoir, bleeder, and lever or pedal.

Finishing the Job

Once clean, bubble-free fluid is flowing, close the bleeder snugly with the box-end wrench — firm enough to seal, but not so hard that you crush the seat or strip the fitting. Pull the tube off and wipe the caliper down. Fill the reservoir to the level marking on the body, reinstall the diaphragm and cap, and clean up any fluid you spilled. Then inspect the bleeder and the banjo fittings at the caliper and master cylinder for weeping, and give the lever and pedal a few slow strokes to confirm nothing is seeping.

Testing Before You Ride

With the bike still supported, spin each wheel by hand to confirm the brakes are not dragging. Then check feel: the lever and pedal should be firm and consistent, and should hold steady under a long, hard squeeze rather than slowly sinking toward the grip. Take the bike to a quiet, safe area and test the brakes at low speed before riding normally. If the lever firms up only after several pumps, there is still air in the system.

When to Take It to a Shop

If the lever will not firm up after several honest bleeding attempts, if bubbles keep appearing no matter how long you work, or if you find fluid weeping from the master cylinder or a caliper, stop and have the bike inspected. The same applies if the reservoir ran dry, if the ABS unit or its lines were disturbed, or if you simply are not confident the system is air-free. On an ABS-equipped machine like the 2019 Z400, a brake system that is not right is not something to ride around and hope improves.

Related Shopping Categories

Shop Brake Fluid for a 2019 Kawasaki ER400 - Z400 ABS Motorcycle.

Shop Brake Lines for a 2019 Kawasaki ER400 - Z400 ABS Motorcycle.

Shop Brake Pads for a 2019 Kawasaki ER400 - Z400 ABS Motorcycle.

Shop Stands for a 2019 Kawasaki ER400 - Z400 ABS Motorcycle.

Shop Brake Tools for a 2019 Kawasaki ER400 - Z400 ABS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.